manualshive.com logo in svg

honle LED Cube 100, Руководство по эксплуатации

Поделиться
Скачать
honle LED Cube 100 Скачать руководство пользователя страница 13

 

 

 

# 69136a 

13 

Mounting the LED Spot 100 

The LED Spot 100 can be mounted on the irradiation chamber in just a few 
steps: 

1.  Loosen the mounting screws (M4X20 flat mushroom-head screws) 

from the rear connection bar (SW 2.5 Allen key) 

2.  Pull back the rear bar (do not remove it completely)  
3.  Place the LED Spot 100 emitter on the irradiation chamber and se-

cure with the two mounting screws 

 
 
 
 
 
 
 
 
 
 
 

 

Fig. 5: Mounting the LED Spot 100 on the LED Cube 100 

 

Connection to the LED powerdrive 

The LED Cube 100 is connected to the LED powerdrive control unit via the 
PLC interface, SUB-D 25: 

  Switch off the LED powerdrive control unit 

  Connect the irradiation chamber to the control unit using a cable 

(SUB-D 25-pin connection cable) 

 

Fig. 6: Connecting the LED Cube 100 to the LED powerdrive  

Mounting the 
LED emitter 

Connection to 
the LED 
powerdrive 

Содержание LED Cube 100





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды