Honeywell VISTA-128BPEN Скачать руководство пользователя страница 90

Страница: 90 / 128

Vista-128BPEN Installation and Setup Guide

6-8

Enter the schedule number (01-20) and time
window number (01-20),

and note the day of the

week the action is desired.

Enter the code for the desired action and
action specifier.

The action codes represent the

events that are to take place when the scheduled
time is reached. Each action also requires an
action specifier, which defines what the action will
affect (relay, relay group, partition, zone list, user
group). The action specifier varies, depending on
the type of action selected.

The following is a list of the Action Codes (desired
actions) used when programming Time-Driven
events. Note that these codes are independent of
the relay codes programmed during

Output

Programming

in the

#93 Menu Mode

Relay Commands

Action Code

Action

Action Specifier

Relay On

Relay #

Relay Off

Relay #

Relay Close for 2 seconds

Relay #

Relay Close XX minutes (set
in field 1*74)

Relay #

Relay Close YY seconds (set
in field 1*75)

Relay #

Relay Group On

Relay Group #

Relay Group Off

Relay Group #

Relay Group Close for 2
seconds

Relay Group #

Relay Group Close XX
minutes (set in field 1*74)

Relay Group #

Relay Group Close YY
seconds (set in field 1*75)

Relay Group #

Arm/Disarm Commands

Action Code

Action

Action Specifier

Arm-STAY

Partition(s)

Arm AWAY

Partition(s)

Disarm

Partition(s)

Force Arm STAY (Auto-
bypass faulted zns)

Partition(s)

Force Arm AWAY (Auto-
bypass faulted zns)

Partition(s)

Arm INSTANT

Partition(s)

26 Arm

MAXIMUM

Partition(s)

•

The auto-arm warning (field 2*06) applies
when using Time-Driven events to auto-arm.

•

Temporary schedules do not override an
auto-arming or auto-disarming programmed
in Time-Driven events.

•

The

auto-arming window cannot be extended

using the Installer Code + #82 Mode.

Bypass Commands

Action Code

Action

Action Specifier

Auto bypass – Zone list

Zone list #

Auto unbypass – Zone list

Zone list #

Open/Close Windows

Action Code

Action

Action Specifier

Enable Opening Window by
partition

Partition(s)

Enable Closing Window by
partition

Partition(s)

Enable Access Window for
access group

Access Group

Access Control Commands

Action Code

Action

Action Specifier

Access Point Grant

Access Point #

Access Point Grant with
Override

Access Point #

Access Point Protect

Access Point #

Access Point Bypass

Access Point #

Access Point Lock

Access Point #

Access Point Exit

Access Point #

Access Point Group Grant

Group #

Access Point Group Grant
with Override

Group #

Access Point Group Protect

Group #

Access Point Group Bypass

Group #

Access Point Group Lock

Group #

Access Point Group Exit

Group #

Access Point Partition Grant

Partition #

Access Point Partition Grant
with Override

Partition #

Access Point Protect by
Partition

Partition #

Access Point Bypass by
Partition

Partition #

Access Point Lock by
Partition

Partition #

Access Point Exit by Partition

Partition #

Access Point Trigger On

Trigger #

Access Point Trigger Off

Trigger #

Access Point Group Enable

Group #

Access Point Group Disable

Group #

Содержание VISTA-128BPEN

































































































































Результаты поиска

Содержание VISTA-128BPEN

Отзывы:

Бренды по названию

Популярные бренды

Honeywell VISTA-128BPEN, Инструкция по установке и настройке

Результаты поиска

Содержание VISTA-128BPEN

Отзывы:

Бренды по названию

Популярные бренды