manualshive.com logo in svg

Honeywell VISTA-128BPEN, Инструкция по установке и настройке

Поделиться
Скачать
Honeywell VISTA-128BPEN Скачать руководство пользователя страница 46

Vista-128BPEN Installation and Setup Guide 

3-26 

To mount and wire the VistaKey module, perform the following steps: 

Step Action 

1 

Mount the VistaKey, door strike or mag lock, and card reader. 

2 

Mount the door status monitor (DSM) and/or request-to-exit (RTE) devices. 

3 Using 

Figure 3-29

 as a reference, connect the card reader interface cable to TB3, 

making the +5V or +12V 

connection last

. 

4 

Connect the leads to TB1 in the following order: 

a.  All ground leads to terminals 2, 5, and 9. 

b.  The DSM, (optional) RTE, and General Purpose leads to terminals 6, 7, and 8, respectively. 

c.  Door strike (or mag lock) lead to terminal 10. 

d.  Local +12V or +24V supply lead to terminal 1. 

e. Local +12V or +24V supply lead to the N/C relay terminal 11 (if a mag lock is being used), 

OR

 to the N/O 

relay terminal 10 (if a door strike is being used). 

5 

Connect the (–) polling loop and (+) polling loop leads (from the VISTA-128BPEN) to terminals 4 and 3, 
respectively. 

6 

Set the Address Select switch to the desired access door number (1-8) 

7 

Repeat steps 1 through 6 for each VistaKey being installed. 

Connecting the Card Reader 

Lead from Reader 

Lead Color 

To VistaKey TB3 

Terminal # 

Green LED 

Orange 

1 

Ground* Black 

2 

DATA 1 (Clock) 

White 

3 

DATA 0 (Data) 

Green 

4 

+5VDC† Red† 6 

+12VDC† Red† 7 

*  TB-3 Terminal 5 is also a ground and may be used 

instead of terminal 2. Terminals 2 and 5 are a common 

ground. 

†  Connect to +5VDC OR +12VDC per reader 

manufacturer’s specification. 

+

WEEKLY TESTING IS REQUIRED
TO ENSURE PROPER OPERATION
OF THIS SYSTEM.

POLE Door Strike/Mag Coil

DATA 1    (WHITE)
DATA 0    (GREEN)

NOTE 1:

 USE UL LISTED ENERGY CABLE FOR ALL CONNECTIONS.

NOTE 2:

 VISTAKEY TB3 TERMINAL 5 IS A GROUND AND MAY BE

USED INSTEAD OF TB3 TERMINAL 2. TB3 TERMINALS 2 AND 5 ARE
A COMMON GROUND.

NOTE 3:

 WHEN USING TRIGGER TO TURN ON AN LED OR BUZZER,

RETURN HIGH SIDE OF LED OR BUZZER TO TB3 TERMINAL 7.
TRIGGER RATING IS 15mA AT 12VDC.

+5V

GND

TRIGGER (SEE NOTE 3)

+12V    (RED)

ZONE C (General)

ZONE A (DSM)

ZONE B (RTE)

POLLING LOOP -

14V MAX (12V @ 85-160mA Nominal)

POLLING LOOP +

GND

GND

GND

N/O DOOR STRIKE POWER

N/C MAG COIL POWER

2
3
4
5
6
7
8

11 12

2 3 4 5 6 7 8 9 10

1

RELAY CONTACT RATINGS:
3A @ 28VDC MAX. (RESISTIVE LOAD)

TB 1

TB 3

1

READER INTERFACE CABLE

GND    (BLACK)

RDR LED    (ORANGE)

TO ALARM SYSTEM
CONTROL PANEL
POLLING LOOP TERMINALS.

NO
CONNECTION

VISTAKEY

THIS DEVICE COMPLIES WITH PART 15 CLASS A
LIMITS OF FCC RULES. OPERATION IS SUBJECT
TO THE FOLLOWING TWO CONDITIONS:
(1) IT MAY NOT CAUSE HARMFUL INTERFERENCE.
(2) IT MUST ACCEPT ANY INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.

K1

DOOR

CONTROL

RELAY

FOR ADDITIONAL RATINGS AND
SPECIFICATIONS, REFER TO
INSTALLATION INSTRUCTION
FOR THE VISTAKEY-SK.

THIS EQUIPMENT SHOULD BE INSTALLED IN
ACCORDANCE WITH THE NATIONAL FIRE
PROTECTION ASSOCIATION'S STANDARDS 70 &
74 (NATIONAL FIRE PROTECTION ASSOC.,
BATTERYMARCH PARK, QUINCY, MA. 02269).
PRINTED INFORMATION DESCRIBING PROPER
MAINTENANCE, EVACUATION PLANNING AND
REPAIR SERVICE IS TO BE PROVIDED WITH
THIS EQUIPMENT.

TO TB1, 11 OR 12

+ 12 VDC TO ONLY
ONE OF THESE INPUTS.
(FROM TB1-1)

 

Figure 3-29: Wiring the VistaKey 

Содержание VISTA-128BPEN

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды