manualshive.com logo in svg

Honeywell VISTA-128BPEN, Инструкция по установке и настройке

Поделиться
Скачать
Honeywell VISTA-128BPEN Скачать руководство пользователя страница 87

Section 6 – Scheduling Options

 

6-5

 

PROMPT 

EXPLANATION

 

 

 

Timed Events  ? 

  1 = YES  0 = NO 

0 

Enter 

1

 to program timed events for relay outputs, additional schedules, and other system functions.  Refer 

to 

Time-Driven Event Programming later in this section for detailed procedures.  

Enter 

0

 to move to the “Access Sched?” prompt. 

 

Access Sched. ? 

  1 = YES  0 = NO 

0 

Enter 

1

 to program access schedules.  Refer to 

Limitation of Access Schedules Programming later in this 

section for detailed procedures.  
Enter 

0

 to move to the “Quit?” prompt. 

 

Quit  ? 

  1 = YES  0 = NO 

0 

Enter 

1

 to quit 

#80 Scheduling Menu Mode and return to normal operating mode.  

Enter 

0

 to make any changes or review the scheduling programming options. If you press 

0

, the “Time 

Window?” prompt is displayed. 

 

Time Windows  

The system provides 20 time windows that are defined 
with start and stop times.  These windows are used for 
various open/close and access schedules, as well as for 
output controls, and are the basis of the scheduling 
system. These windows are shared among all eight 
partitions.   

Time Windows Worksheet

 

The following worksheet is an example of the worksheet 
found in the 

Programming Guide. 

This worksheet will 

help you define time windows and scheduling aspects of 
this system before you program them. Note that time 
windows 

can

 span midnight; for example, from 11 PM 

to 1 AM. 

Time Window 

Number

 

Start Time 

(HH:MM)

 

Stop Time 

(HH:MM)

 

1  

 

2  

 

3…..20  

 

A time window must have a start and a stop time. 

Time Windows Programming 

Enter Scheduling Mode by entering 

Installer Code + 

[#] + [80]

.  The keypad displays the 

Time Window 

Programming

 prompt. 

PROMPT 

EXPLANATION

 

 

 

Time Window  ? 

  1 = YES  0 = NO 

0 

Enter 

1

 at this main menu prompt to program time windows. 

 

Time Window # ? 

01-20,  00 = Quit 01  

Enter the 2-digit time window number 

(01-20)

 to be programmed.  

Press [

✳

] to accept the entry.   Enter 

00 + [

✳

]

 at the “Time Window #?” prompt to quit time window 

programming and display the “Quit ?” prompt.  

 

01 TIME WINDOW 

00:00AM  00:00AM 

If you entered a time window number, the cursor is now positioned on the tens of hours digit of the start of 
window entry.  

Enter the desired start of window hour and press [

✳

].  The cursor moves to the minutes position.  Enter the 

desired minutes and press [

✳

].  Toggle the AM/PM indication by pressing any key 0-9 while the cursor is 

under the A/P position and then press [

✳

].  Repeat this to program the stop of window entry. 

When the entry is completed, the “Time Window #?” prompt is displayed again.  

Enter the next time window number to be programmed and repeat the procedure. 

 

Quit ? 

  1 = YES  0 = NO 

0 

Enter 

0

 at the Quit ? prompt to return to the main menu choices and continue programming.  

Enter 

1

 to quit Scheduling Menu Mode. 

 

 

Because the time windows are shared among all partitions, it is important to make sure that changing a 
time window does not adversely affect desired actions in other partitions. 

 

Содержание VISTA-128BPEN

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды