manualshive.com logo in svg

Honeywell TRADELINE VR8345M, Руководство пользователя, Страница: 11 / 20

Поделиться
Скачать
Honeywell TRADELINE VR8345M Скачать руководство пользователя страница 11

11

68-0160

Fig. 11—VR8345 wiring connections in direct spark ignition system (single rod application).

24V

24V (GND)

S87 CONTROL MODULE

ALARM

VALVE

VALVE

GND

TEMPERATURE 
CONTROLLER

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD 
PROTECTION AS REQUIRED.  

ALTERNATE LIMIT CONTROLLER LOCATION.

MAXIMUM IGNITER-SENSOR CABLE LENGTH:  3 ft [.9 m] OR LESS.

3A REPLACEABLE FUSE.

ALARM TERMINAL PROVIDED ON SOME MODELS.

M8438

MV

MV

L1

(HOT)

L2

1

2

1

2

3

VR8345
COMBINATION
GAS CONTROL

Q347 IGNITER-SENSOR

BURNER

4

4

5

IGNITER-SENSOR AND 
BURNER GROUND

3

5

ALARM, IF USED

QUICK 
CONNECTS

DSI WIRE
ADAPTER

Startup and Checkout

OFF: Prevents main burner gas flow.
ON: Permits main burner gas flow. Under control of the

thermostat and ignition module, gas can flow to the
main burner.

NOTE: Gas controls are shipped with the gas control knob in

the ON position.

PERFORM GAS LEAK TEST

WARNING

FIRE OR EXPLOSION HAZARD
CAN CAUSE PROPERTY DAMAGE,
SEVERE INJURY, OR DEATH

Check for gas leaks with a rich soap and water
solution anytime work is done on a gas control.

GAS LEAK TEST

1. Paint all pipe connections upstream of the gas control

with a rich soap and water solution. Bubbles indicate a gas
leak.

2. If a gas leak is detected, tighten the pipe connection.

WARNING

FIRE OR EXPLOSION HAZARD
CAN CAUSE PROPERTY DAMAGE,
SEVERE INJURY, OR DEATH

1. Do not force the gas control knob. Use only your

hand to turn the gas knob. Never use any tools.

2. If the gas control knob will not operate by hand,

call a qualified service technician to replace the
gas control.

GAS CONTROL KNOB SETTINGS

The gas control knob operates differently in intermittent

pilot, hot surface and direct spark ignition systems.

The gas control knob settings for an intermittent pilot

system are:

OFF: Prevents pilot and main burner gas flow.
ON: Permits gas to flow into the control body. Under

control of the thermostat and intermittent pilot mod-
ule, gas can flow to the pilot and main burner.

The gas control knob settings for hot surface or direct

spark ignition systems are:

VR8345M

INSTALLATION  •  STARTUP AND CHECKOUT

Содержание TRADELINE VR8345M





















Отзывы:

Нет отзывов