manualshive.com logo in svg

Honeywell TotalPlant LCN, Установка системы

Поделиться
Скачать
Honeywell TotalPlant LCN Скачать руководство пользователя страница 25

LCN System Installation

3-9

9/96

3.5.2

3.5.2  Complexing for an Inline Configuration

The following steps are required for the joining of two stations together.  The complexing
tie plates (2) are attached to one station, the second station is set in place next to the first,
the flexible spacers are inserted, and then the second station is bolted to the two tie plates.

1. Install a Wedge Tie Plate Inline, 51403124-100, to the front of the bottom corner of

one of the two stations bases.  See Figure 3-4.

2. Install a Tie Plate Inline, 51308056-100, under the keyboard of the same station.

See Figure 3-4.

3. Place the second station next to the first station.

4. Insert the two long bolts to the keyboards of each station.  Start a nut on each bolt.

5. Insert the Inline Wedge Assembly, 51202034-100, between the keyboards and

tighten the nuts.

12559

Figure 3-7 — Straight-Line Complexed Operator Interface Stations with Wedges

Содержание TotalPlant LCN





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды