Honeywell ORBIT 7120PLUS Скачать руководство пользователя страница 92

Страница: 92 / 241

Orbit 7120plus/7190g User Guide

F1 is the “Send all characters” command

0D is the hex value for a CR

The data is output as:

34567890
<CR>

Stop suppressing characters

Disables suppress filter and clear all suppressed characters.

Syntax = FC.

Replace characters

Replaces up to 15 characters in the output message, without moving the cursor.
Replacement continues until the E5 command is encountered.

Syntax =

E4nnxx

...zz

where nn is the total count of the number of characters

in the list (characters to be replaced plus replacement characters); xx

defines

characters to be replaced and xx

defines replacement characters, continuing

through zz

and zz

E4 Example: Replace zeros with CRs in bar code data

If the bar code has characters that the host application does not want included,
you can use the E4 command to replace those characters with something else. In
this example, you will replace the zeros in the bar code above with carriage returns.

Command string:

E402300DF10D

E4 is the “Replace characters” command

02 is the total count of characters to be replaced, plus the replacement characters
(0 is replaced by CR, so total characters = 2)

30 is the hex value for 0

0D is the hex value for a CR (the character that will replace the 0)

F1 is the “Send all characters” command

0D is the hex value for a CR

The data is output as:

1234
5678
ABC
<CR>

Содержание ORBIT 7120PLUS


















































































































































































































































Результаты поиска

Содержание ORBIT 7120PLUS

Отзывы:

Похожие инструкции для ORBIT 7120PLUS

Бренды по названию

Популярные бренды

Honeywell ORBIT 7120PLUS, Руководство пользователя

Результаты поиска

Содержание ORBIT 7120PLUS

Отзывы:

Похожие инструкции для ORBIT 7120PLUS

Бренды по названию

Популярные бренды