Honeywell ORBIT 7120PLUS Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 241

Honeywell ORBIT 7120PLUS Скачать руководство пользователя страница 60

46

Orbit 7120plus/7190g User Guide

Character Activation Mode

Y2ou may use a character sent from the host to trigger the scanner to begin scan-
ning. When the activation character is received, the scanner continues scanning
until either the

Character Activation Timeout

(page 47), the deactivation character

is received (see

Deactivation Character

on page 48), or a bar code is transmitted.

Scan the following

On

bar code to use character activation, then use Activation

Character (following) to select the character you will send from the host to start
scanning.

Default = Off.

Activation Character

This sets the character used to trigger scanning when using Character Activation
Mode. On the

ASCII Conversion Chart (Code Page 1252)

, page 214, find the hex

value that represents the character you want to use to trigger scanning. Scan the

[ESC] b,

Razz or error tone to indicate a menu change was unsuccessful.

[ESC] 1,

The white LED illuminates for 135 milliseconds followed by a pause.

[ESC] 2,

The white LED illuminates for 2 seconds followed by a pause.

[ESC] 3,

The white LED illuminates for 5 seconds followed by a pause.

[ESC] 4,

Emits a beep at a low pitch.

[ESC] 5,

Emits a beep at a medium pitch.

[ESC] 6,

Emits a beep at a high pitch.

[ESC] 7,

Beeps to indicate a successful decode and communication to host.

[ESC] 8,[ESC] 8,

Razz or error tone to indicate a decode/communication to host was
unsuccessful.

Command

Action

* Off

On

«
...
58
59
60
61
62
...
»

Содержание ORBIT 7120PLUS


















































































































































































































































Отзывы:

Нет отзывов