Honeywell ORBIT 7120PLUS Скачать руководство пользователя страница 133 | Manualshive

Страница: 133 / 241

Honeywell ORBIT 7120PLUS Скачать руководство пользователя страница 133

Orbit 7120plus/7190g User Guide

119

Default = Don’t Require 5 Digit Addenda.

Addenda Timeout

You can set a time during which the scanner looks for an addenda. If an addenda is
not found within this time period, the data can be either transmitted or discarded,
based on the setting you are using for

EAN/JAN-13 Addenda Required

. Set the

length (in milliseconds) for this timeout by scanning the bar code below, then set-
ting the timeout (from 0-65535 milliseconds) by scanning digits from the

Programming Chart,

beginning on page 225 of this manual, then

Save

.

Default =

100.

Note:

The Addenda Timeout setting is applied to all addenda and coupon code searches.

EAN/JAN-13 Addenda Separator

When this feature is

On

, there is a space between the data from the bar code and

the data from the addenda. When turned

Off

, there is no space.

Default

=

On.

Note:

If you want to enable or disable EAN13 with Extended Coupon Code, refer to

EAN-13 with Extended Coupon Code

* Don’t Require

5 Digit Addenda

Require 5 Digit Addenda

Addenda Timeout

* On

Off

«
...
131
132
133
134
135
...
»

Содержание ORBIT 7120PLUS


















































































































































































































































Отзывы:

Нет отзывов