Honeywell ORBIT 7120PLUS Скачать руководство пользователя страница 137

Страница: 137 / 241

Orbit 7120plus/7190g User Guide

123

MSI Check Character

Different types of check characters are used with MSI bar codes. You can program
the scanner to read MSI bar codes with Type 10 check characters.

Default

Validate Type 10, but Don’t Transmit.

When Check Character is set to

Validate Type 10/11 and Transmit

, the scanner

will only read MSI bar codes printed with the specified type check character(s), and
will transmit the character(s) at the end of the scanned data.

When Check Character is set to

Validate Type 10/11, but Don’t Transmit,

the unit

will only read MSI bar codes printed with the specified type check character(s), but
will not transmit the check character(s) with the scanned data.

* Validate Type 10, but Don’t

Transmit

Validate Type 10 and Transmit

Validate 2 Type 10 Characters,

but Don’t Transmit

Validate 2 Type 10 Characters

and Transmit

Validate Type 11 then Type 10

Character, but Don’t Transmit

Validate Type 11 then

Type 10 Character and Transmit

Disable MSI Check Characters

Содержание ORBIT 7120PLUS


















































































































































































































































Результаты поиска

Содержание ORBIT 7120PLUS

Отзывы:

Honeywell ORBIT 7120PLUS, Руководство пользователя, Страница: 137 / 241

Результаты поиска

Содержание ORBIT 7120PLUS

Отзывы: