manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, Руководство пользователя, Страница: 79 / 241

Поделиться
Скачать
Honeywell ORBIT 7120PLUS Скачать руководство пользователя страница 79

CHAPTER

5

Orbit 7120plus/7190g User Guide

65

DATA FORMAT

Data Format Editor Introduction

You may use the Data Format Editor to change the scanner’s output. For example, 
you can use the Data Format Editor to insert characters at certain points in bar 
code data as it is scanned. The selections in the following pages are used only if 
you wish to alter the output. 

Default Data Format setting = None.

Normally, when you scan a bar code, it is output automatically. However, when you 
create a format, you must use a “send” command (see 

Send Commands

 on page 

68) within the format program to output data.

Multiple formats may be programmed into the scanner. They are stacked in the 
order in which they are entered. However, the following list presents the order in 
which formats are applied:

1. Specific Terminal ID, Actual Code ID, Actual Length

2. Specific Terminal ID, Actual Code ID, Universal Length

3. Specific Terminal ID, Universal Code ID, Actual Length

4. Specific Terminal ID, Universal Code ID, Universal Length

5. Universal Terminal ID, Actual Code ID, Actual Length

6. Universal Terminal ID, Actual Code ID, Universal Length

7. Universal Terminal ID, Universal Code ID, Actual Length

8. Universal Terminal ID, Universal Code ID, Universal Length

The maximum size of a data format configuration is 2000 bytes, which includes 
header information. 

If a bar code is read that fails the first data format, the next data format, if there is 
one, will be used on the bar code data. If there is no other data format, the raw data 
is output. 

Содержание ORBIT 7120PLUS


















































































































































































































































Отзывы:

Нет отзывов