Honeywell NOTIFIER UDACT-2 Скачать руководство пользователя страница 21

Страница: 21 / 52

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

Relay Driver (Auxiliary Output) Connections - TB4

Installation and Wiring

When the UDACT-2 is programmed for “Receive/Transmit”, EIA-485 supervision and UDACT-2 trouble status are automatically han-

dled by the host control panel. The relay output may, however, be used for UDACT-2 communications failure if desired.

Figure 2.16 Relay Driver Connections

Relay Energized LED

DPDT Contacts
10 Amps @115 VAC

SPDT Contacts
10 Amps @115 VAC

act-2

lays.wmf

Relay Energized LED

UDACT-2

MR-101/C

MR-201/C

UDACT-2

SLC from FACP

Continuation of SLC

FMM-1*

47K EOL Resistor
(included)

Uda

ct-

2 m

onitr

.wm

(MR-201/C may be used)

*If the SLC device does not match the one in this figure, refer to the SLC manual appendix, which contains wiring conversion charts for type V and type H modules.

Figure 2.17 Monitoring for UDACT-2 Trouble

NOTE:

An FMM-1 Monitor Module is used to supervise the Normally Open output of MR-101/C. If a Trouble Condition or

Communication Failure occurs on the UDACT-2, the MR-101/C relay contact will close, causing the FMM-1 to transmit a

trouble condition to the FACP.

UDACT-2

MR-101/C

Note: The NO contact is
used, as the relay is
normally energized to
ensure a trouble is
generated when power to
the unit is lost.

Содержание NOTIFIER UDACT-2





















































Результаты поиска

Содержание NOTIFIER UDACT-2

Отзывы:

Похожие инструкции для NOTIFIER UDACT-2

Бренды по названию

Популярные бренды

Honeywell NOTIFIER UDACT-2, Инструкция по эксплуатации

Результаты поиска

Содержание NOTIFIER UDACT-2

Отзывы:

Похожие инструкции для NOTIFIER UDACT-2

Бренды по названию

Популярные бренды