Honeywell NOTIFIER UDACT-2 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 52

background image

UDACT-2 — Instruction Manual

P/N 54089:B3 10/29/2019

43

AM2020/AFP1010 (UL 8th)

Panel-Specific Information

Below is a remote installation of a UDACT-2 with an NCA-2 using power supplied by an AMPS-24/E:

A.5 AM2020/AFP1010 (UL 8th)

A.5.1 General

The UDACT-2 is capable of reporting up to 2,040 ACS points when used with the AM2020/AFP1010. For the UDACT-2 to correctly
report a point to the Central Station, both the FACP and the UDACT-2 must have each point programmed as the same function type
(refer to “Zone and Point Assignments” on page 26). If a UDACT-2 point does not match the panel point in function, the point will

default to fire alarm and a fire alarm signal will be transmitted to the Central Station.

A.5.2 Mounting

The UDACT-2 may be mounted in the AM2020/AFP1010 control panel enclosure or be mounted remotely using an ABS-8RB, UBS-
1B, or UBS-1R enclosure. The unit must be placed within the same room and within 20 feet (6.1 meters) of the panel. Wiring must be

enclosed in conduit.

A.5.3 Wiring

Connections

Refer to Figures A.12 and A.13.
Connect the communication line between the EIA-485 terminal block on the AM2020/AFP1010 and EIA-485+ and EIA-485- terminals

on TB2 on the UDACT-2, being certain to observe polarity.
If the UDACT-2 is the only or last device connected to the EIA-485, set SW1 DIP 1:4 to ON to enable the UDACT-2’s 120 ohm termi-
nating resistor.
Connect the Ground Wire (PN 71073, provided) from the UDACT-2

EARTH

terminal on TB2 to the CHS-4 Chassis or to a solid building

earth ground.

CAB-3/4 Series Cabinet

To supervised

phone lines

Solid earth ground

EIA-485

(ACS Mode)

TB7 on NCA-2

+24 VDC

non-resettable power

TB3 AUX 24 output

on AMPS-24.

BB-100 or BB-200 Cabinet

Wires in conduit

Remote Cabinet

Figure A.11 UDACT-2 and NCA-2 powered by AMPS-24/E

NOTE:

The UDACT-2 does not support voice and burglary options when used with the AM2020/AFP1010. Refer to the panel’s

Installation Manual for additional restrictions and more information.

!

CAUTION:

REMOVE ALL POWER FROM THE CONTROL PANEL BY DISCONNECTING AC AND BATTERIES BEFORE MAKING

ANY CONNECTIONS TO PREVENT PERSONAL AND/OR CIRCUIT DAMAGE.

«
...
41
42
43
44
45
...
»

Содержание NOTIFIER UDACT-2





















































Отзывы:

Нет отзывов

Похожие инструкции для NOTIFIER UDACT-2

Бренд: M-system Страницы: 4

Бренд: M-system Страницы: 7

Бренд: YouKits Страницы: 1

Efector 600 TA3233

Бренд: IFM Electronic Страницы: 3

Бренд: M-system Страницы: 5

Бренд: Lectrosonics Страницы: 14

Class B Transceiver NAIS-300

Бренд: Navico Страницы: 24

Бренд: Midland Страницы: 24

Бренд: Midland Страницы: 36

Бренд: Midland Страницы: 58

Бренд: JVC Страницы: 2

Kenwood TK-5220

Бренд: JVC Страницы: 128

Бренд: TWIG Страницы: 2

Бренд: Magnum Страницы: 9

Бренд: Midland Страницы: 17

Бренд: Midland Страницы: 46

Бренд: Sigma Страницы: 3

TorqueTrak 10K-LP

Бренд: Binsfeld Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды