Honeywell JOSI-DBC012-N11 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 40

background image

Document 800-01605 Rev A

35

04/08

B

Cable Guidelines

Power supply cable maximum length (feet/meters)

Wire gauge

Total
load

Power
supply

24 AWG

22 AWG

18 AWG

16 AWG

Cameras with AC/DC power supplies

3.5 W

15 VDC

180/55

290/88

730/220

1170/352

3.5 W

24 VAC

470/143

760/232

1926/587

3065/934

Note

Calculations are based on an unregulated linear power supply which
would be the worst case. Using a regulated or switching power
supply can increase the cable distance. We recommend using a CSA
Certified/UL listed Class 2

power adapter to ensure compliance with

electrical safety standards.

Note

Calculations are based on a 15VDC power supply to allow for longer
cable runs.

Video cable maximum length (feet/meters)

Cable type

RG-59

RG-6

RG-11

Wire gauge

23 AWG*

18 AWG*

14 AWG*

Maximum length (feet/meters)

750/229

1500/457

2000/610

* Copper clad steel core, 95% braided shield

We recommend these NVT video transceivers (sold separately by NVT Inc.):

NV-212A (500 ft/152 m—26

Ω

)**

NV-213A/A-M (1000 ft/305 m—52

Ω

)**

NV-652R, NV-862R or NV-1662R (3000 ft/914 m—163

Ω

)**

** Distances have been calculated using 24 AWG Twisted Pair wire.

Note

We recommend that you measure the wire distance to ensure the
capability of the twisted pair product is not exceeded. Use an
ohmmeter to measure wire resistance by shorting the two conductors
together at the far end, then measure the loop resistance out and
back. Compare to the table below.

Maximum length (feet/meters)

AWG

250/76

500/152

1000/305

1500/457

2000/610

18

3

Ω

6

Ω

13

Ω

19

Ω

26

Ω

20

5

Ω

10

Ω

20

Ω

30

Ω

40

Ω

22

8

Ω

17

Ω

33

Ω

48

Ω

66

Ω

24

13

Ω

26

Ω

52

Ω

78

Ω

108

Ω

Note

Use point-to-point Unshielded Twisted Pair wire only.

«
...
33
34
35
36
37
...
»

Содержание JOSI-DBC012-N11









































Отзывы:

Нет отзывов

Похожие инструкции для JOSI-DBC012-N11

Бренд: Zivif Страницы: 14

Бренд: YESKAMO Страницы: 28

WJND400 - NETWORK DISK RECORDER

Бренд: Panasonic Страницы: 21

BB-HCM381A - Network Camera

Бренд: Panasonic Страницы: 4

Бренд: FBII Страницы: 83

Бренд: FBII Страницы: 10

Бренд: NA-DE Страницы: 8

Бренд: i-PRO Страницы: 17

Бренд: Eneo Страницы: 16

Бренд: Vega Absolute Страницы: 26

Бренд: HuddleCamHD Страницы: 18

Бренд: Takex Страницы: 8

Бренд: SAFE-T-ALERT Страницы: 5

Бренд: Black Страницы: 27

Бренд: TeleCare Страницы: 8

ThermoVisualizer

Бренд: LaserLiner Страницы: 88

Бренд: AJAX Страницы: 13

Бренд: Omega Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды