Honeywell #HZ-7000 - Sure-set Digital Heater Fan Скачать руководство пользователя страница 49

Страница: 49 / 74

UltraKey Plus Controller Installation and User Guide

Document 800-02573 Rev B

11/2009

If the current mode is VB mode, change it to MAXPRO mode by pressing the Mode
VB button

and

logging into the Setting menu again.

Press Hardware Config.
The current controller setting is displayed.

Press Port Settings and then Ethernet.
The Ethernet

Setting

are

display

Press IP Address and use the numeric keypad or LCD Touch Panel to enter an IP
address, as required.

Press Subnet Mask, and enter a NetMask as required. Press Enter.

Press Default Gateway. Using the number key or LCD Touch Panel to enter a
Gateway, as required. Press Enter.

10. Press Sys.Cntl.IP Address, using the number key or LCD Touch Panel to enter the

address of the device, as required. Press Enter.

11. Press Save to exit from the Ethernet Settings menu.

Step 3: Configure Address and Joystick Speed

To configure the address and joystick speed:

Press

Quit

to exit from the Port Settings menu.

Press

Keyboard Address

to select an address between 1 and 99 to assign to the

controller. You can also use the numeric keypad to enter a number between 1 and 99.

Press Enter to save the address and exit the configuration menu.

Press Joystick Res to select Low or High.

Press Save.
A message confirming the operation displays.
Press Yes to save or No to cancel.

Step 4: Configure the Controller for MAXPRO Mode

To configure the controller for MAXPRO mode:

Press Users Menu

to display the configuration screen.

See

User Menus

on page

to configure the device.

Press Home and then Quit to exit when the configuration is finished.

Note

Serial Port and Ethernet can not be used at the same time in MAXPRO mode.

Содержание #HZ-7000 - Sure-set Digital Heater Fan











































































Результаты поиска

Содержание #HZ-7000 - Sure-set Digital Heater Fan

Отзывы:

Бренды по названию

Популярные бренды

Honeywell #HZ-7000 - Sure-set Digital Heater Fan, Инструкция по установке и эксплуатации

Результаты поиска

Содержание #HZ-7000 - Sure-set Digital Heater Fan

Отзывы:

Бренды по названию

Популярные бренды