Honeywell #HZ-7000 - Sure-set Digital Heater Fan Скачать руководство пользователя

Страница: 34 / 74

Installing UltraKey Plus with VideoBloX

Note

The default baud rate for VideoBloX is 19200 bps. It is recommended that you
do not change this setting.

Press DataBit to select 7 bit or 8 bit.

10. Press parity to select Even, Odd or None.

11. Press Stop Bit to select 1 bit or 2 bit.

12. Press Save, and then Quit.

13. If you are using the TCP/IP to connect to a VideoBloX NetCPU, press Ethernet.

Note

In this field, you are setting the VideoBloX Netcpu IP address. To set the
UltraKey Plus IP address, see

Step 2: Set and Configure for an Ethernet

Connection

, page

Step 3: Configure Address

To configure the controller address:

Press Quit to exit from Port Settings menu.

Press Keyboard Addr to select an address between 1 and 32 to assign to the
controller. You can also use the numeric keypad to enter a number between 1 and 32.
Entering a number greater than 32, makes this operation invalid.

Press Enter to save the address and exit the configuration menu.

Step 4: Configure the Controller for VideoBloX Mode

To configure the controller for VideoBloX mode:

Press Users Menu

to display the configuration screen.

Refer to

User Menus

on page

to configure the device.

Press Home and then Quit to exit when the configuration is finished.

Содержание #HZ-7000 - Sure-set Digital Heater Fan











































































Результаты поиска

Содержание #HZ-7000 - Sure-set Digital Heater Fan

Отзывы:

Похожие инструкции для #HZ-7000 - Sure-set Digital Heater Fan

Бренды по названию

Популярные бренды

Honeywell #HZ-7000 - Sure-set Digital Heater Fan, Инструкция по установке и эксплуатации

Результаты поиска

Содержание #HZ-7000 - Sure-set Digital Heater Fan

Отзывы:

Похожие инструкции для #HZ-7000 - Sure-set Digital Heater Fan

Бренды по названию

Популярные бренды