background image

4

D

INITIAL INSTALLATION

PREPARATION

Before beginning the assembly of this product, ensure all parts are present. Compare all parts with the package contents list 

and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product. 
Estimated assembly time: 2 hours
Tools required (not included): Electrical tape, Phillips Screwdriver, Safety Glasses, Step Ladder, and Wire Strippers.
1. Turn off power to the fan at the breaker box and the wall switch (Figure 1.1). 

DANGER:

 Failure to disconnect the power supply 

prior to installation may result in serious injury or death.

2. Choose one of the following mounting options (Figure 1.2) :

    Standard Mount

 - best suited for ceilings 8 feet or higher. For very high ceilings, use a longer downrod (not included). 

Angle Mount 

- best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade 

clearance. Ensure the ceiling angle is not steeper than 16 degrees. 

Flushmount Installation 

- not available for this model. 

Closemount Installation

 - best suited for ceilings 8 feet or lower. 

3. Choose a suitable location - Ensure the blades will be at least 30 inches from any obstructions. Also check the downrod 

length to ensure the blades will be at least 7 feet above the floor (Figure 1.3). 

1. Loosen all four mounting bracket screws and completely remove the two screws from the round holes in the canopy. Then 

remove mounting bracket from the canopy and save the screws for later (Figure 2.1). 

2. Install the mounting bracket to the outlet box (sold separately) using the screws and washers provided with the outlet box 

(Figure 2.2).

3. Remove the 10 motor screws from the underside of the motor. Discard the motor blocks, but save the motor 

screws for installation of the blade arms (Figure 2.3).

 

For CLOSEMOUNT INSTRUCTIONS, skip to page 6.

Figure 1.1

Figure 2.1

Figure 1.2

Standard and 

Closemount

Angle Mount

Motor Screw

Figure 2.2

Figure 2.3

Figure 1.3

Standard Mount

Flushmount

Angle Mount

Closemount

 

Mounting 

Bracket Screw

Canopy

7 ft. min.

30in. min.

Содержание Glencrest











Отзывы: