background image

9

TROUBLESHOOTING

The fan does not move.

The fan is noisy.

The fan wobbles 

excessively.

The fan operates 

correctly but the lights 
are not working

1. Firmly push the reverse switch completely left or right.

2. Make sure the wall switch is turned on.

3. Turn the power on or check the fuse (breaker).

4. Turn the power off and check all connections at the ceiling outlet box.

1. Check and tighten all screws that hold the fan blades to the blade arms and the motor.

2. Replace the cracked blade.

3. Do not use a full range dimmer switch to control the fan speed.

4. Ensure the outlet box is secured to the building structure.

5. Ensure the mounting bracket is secured to the outlet box and that the screws are tight.

1. Ensure the 9-pin connectors are properly secured.

2. Turn the power off and check all connections at the ceiling outlet box.

1. Check and tighten all screws that hold the fan blades to the blade arms and the blade arms to the 

motor.

2. Switch one blade with a blade from the opposite side, or balance the fan using the blade 

balancing kit.

3. Turn off the power. Loosen the canopy and verify that the mounting bracket is secure to the 

electrical outlet box. The bracket must be flush without movement against the outlet box. Verify 

the outlet box is secure.

4. Use a longer downrod (sold separately) or move the fan to another location.

5. Lift up the yoke cover and tighten the set screws on the yoke until secure.

PROBLEM

CORRECTIVE ACTION

 

Warning:

 Shut off the power supply before you begin any maintenance task. 

Содержание Glencrest











Отзывы: