manualshive.com logo in svg

Honeywell FSL100-IR3, Техническое руководство

Продукт Honeywell FSL100-IR3 - это высокотехнологичный инфракрасный датчик для обнаружения пламени. Бесплатное техническое руководство и руководство по эксплуатации можно скачать со страницы нашего веб-сайта. {веб-сайт} - ваш источник надежной информации.

Поделиться
Скачать
background image

CONTENTS

 

MAN0987_Iss 2_09/16 

1 

FSL100 Series Flame Detectors 

Technical Handbook 

 

 

 

Contents

 

1 

Introduction ............................................................................................................................................................................ 3

 

1.1 

Intended Readers ............................................................................................................................................................. 3 

2 

Safety Hazards, Warnings and Cautions ............................................................................................................................. 5

 

2.1 

General Warnings and Cautions ....................................................................................................................................... 5 

2.2 

Important Information ........................................................................................................................................................ 5 

2.3 

FSL100 Safety Features ................................................................................................................................................... 6 

3 

Overview ................................................................................................................................................................................. 7

 

4 

Mechanical Installation .......................................................................................................................................................... 9

 

4.1 

Siting ................................................................................................................................................................................. 9 

4.2 

Mounting and Orientation .................................................................................................................................................. 9 

4.3 

Installing the FSL100 Flame Detectors ............................................................................................................................. 9 

4.4 

Cone of Vision ................................................................................................................................................................ 10 

4.5 

Shadow Effect ................................................................................................................................................................. 10 

4.6 

Mounting Below a Ceiling ............................................................................................................................................... 11 

4.7 

Vote Count ...................................................................................................................................................................... 12 

4.8 

Weather Protection ......................................................................................................................................................... 13 

4.9 

Hot Work ......................................................................................................................................................................... 13 

5 

Electrical Installation ............................................................................................................................................................ 15

 

5.1 

Power Supply .................................................................................................................................................................. 15 

5.2 

Cabling Recommendations ............................................................................................................................................. 15 

5.3 

Earth (Ground) Regimes ................................................................................................................................................. 15 

5.4 

Wiring Diagram ............................................................................................................................................................... 16 

5.5 

Electrical Connection (General) ...................................................................................................................................... 17 

5.6 

Wiring to a Controller (General) ...................................................................................................................................... 17 

5.7 

Wiring to a Fire Control Panel ......................................................................................................................................... 18 

5.8 

Wiring to a PLC ............................................................................................................................................................... 19 

5.9 

Wiring to a 4-20 mA Non-Isolated (Sourcing) Current Output ......................................................................................... 19 

5.10  Connecting the Manual Self-Test .................................................................................................................................... 19 

5.11  FSL100 Latching Alarm Settings .................................................................................................................................... 20 

6 

Commissioning and Testing ................................................................................................................................................ 21

 

6.1 

Commissioning ............................................................................................................................................................... 21 

6.2 

Functional Testing .......................................................................................................................................................... 22 

6.3 

Fault Analysis ................................................................................................................................................................. 22 

6.4 

Fault Testing ................................................................................................................................................................... 23 

7 

FSL100 Operation ................................................................................................................................................................. 25

 

7.1 

The Display LEDs ........................................................................................................................................................... 25 

7.2 

Normal Operation ........................................................................................................................................................... 25 

7.3 

Fault Conditions .............................................................................................................................................................. 25 

7.4 

Relay Outputs ................................................................................................................................................................. 25 

7.5 

Analogue Output 0

–20 mA (Stepped, Sinking, Non-Isolated) ......................................................................................... 25 

7.6 

Self-Testing..................................................................................................................................................................... 25 

7.7 

Manual Self-Test ............................................................................................................................................................. 26 

8 

Maintenance .......................................................................................................................................................................... 27

 

9 

FSL100-SM21 Swivel Mount ................................................................................................................................................. 29

 

Содержание FSL100-IR3


























































Отзывы:

Нет отзывов

Похожие инструкции для FSL100-IR3

ABB Welcome M21311P1-A Online Manual preview
Welcome M21311P1-A
Бренд: ABB Страницы: 15
Cam Scan CS-PTZ8800 Manual preview
CS-PTZ8800
Бренд: Cam Scan Страницы: 7
Omni OMNI-624 Installation And Setup Manual preview
OMNI-624
Бренд: Omni Страницы: 108
Wansview W7 Installation Manual preview
W7
Бренд: Wansview Страницы: 12
Digital Watchdog B2372TIR Instruction Manual preview
B2372TIR
Бренд: Digital Watchdog Страницы: 3
Grundig GCA-B3323V Owner'S Manual preview
GCA-B3323V
Бренд: Grundig Страницы: 25
Nice HSSOC Instructions And Installation For Use preview
HSSOC
Бренд: Nice Страницы: 12
Advent home navigator User Manual preview
home navigator
Бренд: Advent Страницы: 32
GST DI-M9103 Manual preview
DI-M9103
Бренд: GST Страницы: 2
SWiiD SWIIDCAM+ Installation And User Manual preview
SWIIDCAM+
Бренд: SWiiD Страницы: 16
Samcon ExCam Series T08 Installation Manual preview
ExCam Series T08
Бренд: Samcon Страницы: 52
Genie TPH-4000P Quick Start Manual preview
TPH-4000P
Бренд: Genie Страницы: 6
i-PRO WV-S2536L Installation Manual preview
WV-S2536L
Бренд: i-PRO Страницы: 2
Abus Eyseo TVCC35000 User Manual preview
Eyseo TVCC35000
Бренд: Abus Страницы: 63
ALC SIGHT HD AWF50 User Manual preview
SIGHT HD AWF50
Бренд: ALC Страницы: 50
PNI House WiFi550 User Manual preview
House WiFi550
Бренд: PNI Страницы: 84
EverFocus EMW990F User Manual preview
EMW990F
Бренд: EverFocus Страницы: 10
Winland WaterBug WB-800 Installation & Operation Instructions preview
WaterBug WB-800
Бренд: Winland Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды