Honeywell FSL100-IR3 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 57

background image

MAN0987_Iss 2_09/16

43

FSL100 Series Flame Detectors

Technical Handbook

CERTIFICATION

14.4 North American approvals

– cFMus class 3611 & FM class 3260

All drawings and other details are listed in the “Document List FSL100-series flame detector”.

FM approvals for the:

FSL100-UV UV Flame Detector
FSL100-UVIR UVIR Flame Detector
FSL100-IR3 IR3 Flame Detector

Nonincendive per FM class 3611: Class I, II, III, Div. 2, Groups A, B, C, D, F, G
Nonincendive per C22.2 No. 213: Class I, Div. 2, Groups A, B, C, D
Dust-tight per C22.2 No. 25: Class II, III, Div. 2, Groups F, G

Ambient temperature : -25ºC

to +70ºC

Temperature Code: T4 at Ta < +70ºC
Ingress Protection: IP65

Warnings:

1. The power supply of the flame detector must comply with NEC class 2, as described by the National Electrical Code

(ANSI / NFPA 70).

2. Cable used with the flame detector must be PLTC or ITC type as described by the National Electrical Code (ANSI /

NFPA 70); twisted shielded pairs.

3.  When cleaning the swivel mount SM21, exclusively use a damp micro fiber cloth to avoid the mount from getting static.
4.  The screws of the housing lid should be tightened with a torque of 2 Nm.
5.  The screws of the wire terminals should be tightened with a torque of 0.4 Nm.
6.  The alarm- and EOL resistor must be rated 2 W minimum each and the total power dissipation of both alarm- and EOL

resistor should not exceed 2 W.

7.  Substitution of components may impair suitability for division 2.
8.  Do not open when energized.
9.  Explosion hazard. Do not remove or replace while circuit is powered or when a flammable or combustible atmosphere is

present.

10. Explosion hazard. Do not disconnect equipment when a flammable or combustible atmosphere is present.
11. Explosion hazard. Do not disconnect while circuit is powered unless the area is known to be non-hazardous.

-For language translation assistance, contact your local representative, or email:

[email protected]

-Pour la langue de traduction aide, contactez votre représentant local ou envoyez, un e-mail:

[email protected]

Avertissement:

Risque d'explosion. Ne pas débrancher tant que le circuit est sous tension, à moins qu'il ne s'agisse d'un emplacement non
dangereux.

«
...
45
46
47
48
49
...
»

Содержание FSL100-IR3


























































Отзывы:

Нет отзывов

Похожие инструкции для FSL100-IR3

Бренд: Varian Страницы: 176

Бренд: L-Sniper Страницы: 12

Бренд: U-Prox Страницы: 29

Бренд: LaserLine Страницы: 68

STExB2X05-S Series

Бренд: E2S Страницы: 20

Бренд: Securiton Страницы: 10

Бренд: Comtrend Corporation Страницы: 64

Бренд: Sylvania Страницы: 26

Бренд: Digital Watchdog Страницы: 40

Бренд: Dorlen Страницы: 2

Бренд: Pilz Страницы: 25

Бренд: e-Line Technology Страницы: 2

Бренд: Daikin Страницы: 9

Бренд: Iqinvision Страницы: 12

Бренд: Dahua Technology Страницы: 18

Бренд: First Alert Страницы: 44

Бренд: Abus Страницы: 47

Бренд: Avtech Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды