Honeywell EQUIP HD4HDIH Скачать руководство пользователя страница 24

Страница: 24 / 90

Installation and Setup

Connect to Power Input

Caution

When powering the camera from 24V AC, a UPS source should be
used to ensure satisfactory performance.

Connect the power supply that is appropriate for your installation:

•

24V AC power supply

•

Power over Ethernet (IEEE 802.3 af) 48V DC power supply

Note

Connect power either from a 24V AC source or CAT5 Ethernet connector
(PoE). It is not recommended to connect both power sources at the same
time.

Note

If you are using PoE (802.3af), power will automatically be supplied to the
camera through the network cable.

1. Connect to the power supply (see

Figure 2-5

page 24

). Locate the two-pin green

connector that was shipped with your camera and make the necessary connections.

2. Plug the power supply into an appropriate power source. The LED on the RJ45 jack

illuminates to show that the camera is receiving power. If it does not illuminate, check
the terminal block connections and the power source.

Figure 2-5

Wiring Connections Shown on Board

Local video out

Audio: Input / Output
Alarm: Input / Output
(see

Connecting Alarms

, page

)

RJ45 Ethernet Connector
(see

Connecting to a Network via

CAT5 Ethernet Connector

, page

)

This is also the connection for
Power over Ethernet (PoE 802.3af)

Power 24V AC

Содержание EQUIP HD4HDIH



























































































Результаты поиска

Содержание EQUIP HD4HDIH

Отзывы:

Похожие инструкции для EQUIP HD4HDIH

Бренды по названию

Популярные бренды

Honeywell EQUIP HD4HDIH, Руководство пользователя

Результаты поиска

Содержание EQUIP HD4HDIH

Отзывы:

Похожие инструкции для EQUIP HD4HDIH

Бренды по названию

Популярные бренды