Honeywell Dolphin 7600 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 64

background image

32

Troubleshooting

The following guide is for reference purposes only. Contact a customer service
representative to preserve the limited warranty terms.

SYMPTOMS

POSSIBLE CAUSE(S)

SOLUTION

All Interfaces

No LEDs, beep
or motor spin.

No power is being
supplied to the
scanner.

Check transformer, outlet and
power strip. Make sure the
cable is plugged into the
scanner.

No LEDs, beep.

No power is being
supplied to the
scanner from host.

Some host systems cannot
supply enough current to power
7600 series scanner. Use the
power supply included with the
scanner.

3 beeps on
power up.

Non-volatile RAM
failure.

Contact a customer service
representative, if the unit will not
hold the programmed
configuration.

Continuous
razz tone on
power up.

RAM or ROM failure.

Contact a customer service
representative, if the unit will not
function.

Razz tone and
amber LED flash
at power up.

VLD failure.

Contact a customer service
representative.

Razz tone and
both LEDs flash
at power up.

Scanner motor failure.

Contact a customer service
representative.

Multiple scans
upon
presentation of
code.

Same symbol timeout
set too short.

Adjust same symbol timeout for
a longer time.

The unit powers
up, but does
not beep.

Beeper disabled
No volume is selected
No tone is selected.

Enable beeper
Select volume
Select tone.

«
...
34
35
36
37
38
...
»

Содержание Dolphin 7600

































































Отзывы:

Нет отзывов

Похожие инструкции для Dolphin 7600

Бренд: Wasp Страницы: 28

Бренд: Microscan Страницы: 2

Бренд: Netum Страницы: 21

Бренд: IFM Electronic Страницы: 37

Бренд: Bluebird Страницы: 26

Бренд: U-Line Страницы: 3

Бренд: Nordic ID Страницы: 16

Бренд: Nordic ID Страницы: 22

Бренд: Nordic ID Страницы: 58

Бренд: Abit Страницы: 9

ENERGY Book 3050

Бренд: ENERGY SISTEM Страницы: 40

Бренд: Unitech Страницы: 36

Бренд: Pocketbook Страницы: 23

Бренд: Pocketbook Страницы: 45

1D2D TECNOACCESSORI TC-BC2D-12W

Бренд: Tecno Страницы: 29

Charge Analyzer 711

Бренд: 3M Страницы: 27

Бренд: OBD2 Страницы: 10

Бренд: Obreey Страницы: 111

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды