Honeywell Dolphin 7600 Скачать руководство пользователя страница 40

Страница: 40 / 64

SYMPTOMS

POSSIBLE CAUSE(S)

SOLUTION

Characters are
being dropped.

Intercharacter delay
needs to be added to
the transmitted output.

Add some intercharacter delay
to the transmitted output by
using the MetroSelect

Programming Guide
(

00-02407).

Aux port operation with any interface

Trouble with the
Secondary
Scanner.

Refer to the user guide provided
with the secondary scanner.

Secondary
Scanner
powers up but
data is not
relayed to the
host.

Cable [

54-54667]

may not be connected
to the proper port.

Ensure Secondary scanner is
connected to the 7600 com port
marked “Aux” port.

The “Aux” com port
may not be operating
properly.

* The 7600 must be

programmed to enable the
“Aux” port.

The auxiliary input port’s data
format must match the main
output format of the secondary
scanner.

* Use MetroSet

For the Auxiliary interface, choose “HoloTrak Decode”.
All remaining parameters will be automatically chosen.

USB Only

The scanner
Powers up ok,
scans ok but
does not
communicate.

The USB Port is not
operating correctly.

Check that the scanner is
programmed for USB operation.

Check that the host’s USB port
is enabled.

When configured
as USB scanner
razz tone & 3
LED flashes.

USB port is not
operating correctly.

Unplug & plug USB cable at host
end.

Contact a customer service
representative if error continues.

Содержание Dolphin 7600

































































Результаты поиска

Содержание Dolphin 7600

Отзывы:

Похожие инструкции для Dolphin 7600

Бренды по названию

Популярные бренды

Honeywell Dolphin 7600, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Dolphin 7600

Отзывы:

Похожие инструкции для Dolphin 7600

Бренды по названию

Популярные бренды