manualshive.com logo in svg

Honeywell DirectLine DL421, Руководство пользователя, Страница: 31 / 40

Поделиться
Скачать
Honeywell DirectLine DL421 Скачать руководство пользователя страница 31

  

Operation

 

 

2/04 

DirectLine® DL421 Sensor Module User Manual 

25 

5.2  Diagnostic Error Messages 

When a diagnostic error or status condition occurs, the Online Display alternates 
between measured pH and a text message.  
 

Table 5-3   Online Diagnostic Errors 

What you see 

What it is 

What to do 

CNFG 

Data error detected. 

Reset unit or cycle power. 

Second occurrence will show 
FALT. 

FALT 

Unit electronics are defective.  

Replace electronics module. 

These errors may occur when online pH or temperature is displayed. 

P HI 

Measured pH is > 14.00 pH 

Bring process within limits 

P LO 

Measured pH is < 0.00 pH 

Bring process within limits 

PRBE 

Probe is defective, removed from process, or not 
connected. 

Forces the output to burnout level (greater than 
21.8 mA). 

Check probe, connection and 
presence of sample. 

When the source of the error is 
removed, the error will clear and 
the output will return to normal 
operation. 

T HI 

Measured temperature is > 110 

°

C 

Bring process within limits 

T LO 

Measured temperature is < 

−

10 

°

C  

Bring process within limits 

These errors may occur during probe calibration and abort the calibration process. 

FAIL 

These error messages are preceded by the 
message “FAIL”  

BFRS

  The Slope buffer is less than 2 pH from 

Zero (Standardization) buffer. 

SRNG

  The Slope calibration failed due to a 

calculated Percent Theoretical Slope value 
outside the range of 80.0 % to 105.0 %. 

STBL

  The Zero (Standardization) or Slope 

calibration failed due to measured pH 
instability. 

TRNG

  The Zero (Standardization) or Slope 

calibration failed due to solution 
temperature outside the range of 0 

°

C to 50 

°

C. (Auto Buffer Recognition calibration 

only) 

ZRNG

  The Zero (Standardization) calibration 

failed due to a calculated Zero Offset value 
outside the range of –2.00 pH to 2.00 pH. 

Press Mode to return to online 
display. 
 
 

 

Содержание DirectLine DL421









































Отзывы:

Нет отзывов