Honeywell CP-600E Скачать руководство пользователя страница 19

Страница: 19 / 20

WEB-600E AND CP-600E NETWORK CONTROLLERS

62-0433—01

TAB MOUNTING DIMENSIONS

Measurements are in inches and (mm). Note that DIN mounting is recommended over tab mounting. See Fig. 1.

Fig. 10. Tab mounting dimentions.

1-64

DIA.

(4)

3-1/4

(83)

WEB-600E

IO-16-H IO-16-H OR

NPB-PWR-H

NOTE:

DOCUMENT MAY NOT SHOW DIMENSIONS TO SCALE.

VERIFY ALL MEASUREMENTS BEFORE DRILLING.

ELECTRONIC AND PRINTED VERSIONS OF THIS

DIN MOUNTING IS RECOMMENDED OVER TAB MOUNTING.

SEE FIG. 1.

WEB-600E

NPB-PWR-H,

NPB-PWR-UN-H,

OR IO-16-H

NOTE: DISTANCE BETWEEN CENTER OF TABS FROM ONE

UNIT TO ANOTHER UNIT.

TIP: IF MOUNTING ACCESSORY MODULES, FUTURE

REMOVAL/REPLACEMENT OF THE CONTROLLER IS

SIMPLIFIED IF YOU DO NOT INSTALL SCREWS IN

THE “ACCESSORY MODULE SIDE” TABS OF THE

CONTROLLER (SEE ABOVE).

ACCESSORY

MODULE

SIDE TABS

M33924

2-1/2

(64)

6-23/32 (171)

(102)

3-3/4 (95)

2-1/2

(64)

6-23/32 (171)

3-1/4

(83)

3-31/64

(89)

Содержание CP-600E





















Результаты поиска

Содержание CP-600E

Отзывы:

Похожие инструкции для CP-600E

Бренды по названию

Популярные бренды

Honeywell CP-600E, Руководство пользователя

Результаты поиска

Содержание CP-600E

Отзывы:

Похожие инструкции для CP-600E

Бренды по названию

Популярные бренды