Honda BF100D Скачать руководство пользователя страница 97

Страница: 97 / 155

SERVICING YOUR OUTBOARD MOTOR

7. Remove the three screws and

separate the water separator cup

from the body.

8. Thoroughly clean the water

separator cup.

9. Reassemble the water separator in

the reverse order of removal. Use a

new O-ring.



TIGHTENING TORQUE:



3.1 lbf·ft (4.2 N·m, 0.43 kgf·m)

• Assemble so the flat part on the

back of the suspension is parallel to

the water separator joint as shown

below.

10. Connect the water level sensor 2

pin connector. Install the harness

to clip C and the harness clip.



Align the positioning bands on

the harness with the end of clip C

and the harness clip as shown

above.

11. Reinstall the water separator in

the reverse order of removal.

BAFFLE

PLATE

O-RING

(Replace)

BODY

WATER

SEPARATOR CUP

SCREW (3)

SUSPENSION

STRAP

Assemble so the flat part of the

suspension and the water separator joint

are parallel to each other.

JOINT

WATER

SEPARATOR

FLAT PART ON BACK

OF SUSPENSION

POSITIONING

BAND

HARNESS

CLIP

WATER LEVEL

SENSOR 2 pin

CONNECTOR

CLIP C

POSITIONING

BAND

31ZY96300.book 95 ページ２０１３年１０月２１日　月曜日　午前９時２５分

Содержание BF100D




























































































































































Результаты поиска

Содержание BF100D

Отзывы:

Бренды по названию

Популярные бренды

Honda BF100D, Руководство пользователя

Результаты поиска

Содержание BF100D

Отзывы:

Бренды по названию

Популярные бренды