manualshive.com logo in svg

Honda BF100D, Руководство пользователя

Поделиться
Скачать
Honda BF100D Скачать руководство пользователя страница 47

45

BEFORE OPERATION

ARE YOU READY TO GET 

UNDERWAY?

Your safety is your responsibility. A 
little time spent in preparation will 
significantly reduce your risk of 
injury.

Knowledge

Read and understand this manual. 
Know what the controls do and how 
to operate them.

Familiarize yourself with the 
outboard motor and its operation 
before you get underway. Know what 
to do in case of an emergency.

Familiarize yourself with all laws and 
regulations relating to boating and the 
use of outboard motors.

Safety

Always wear a PFD (Personal 
Flotation Device) while on the boat.

Attach the emergency stop switch 
clip securely to the operator or to the 
operator’s PFD (Personal Flotation 
Device).

IS YOUR OUTBOARD 

MOTOR READY TO GO?

For your safety, and to maximize the 
service life of your equipment, it is 
very important to take a few moments 
before you operate the outboard 
motor to check its condition.

Be sure to take care of any problem 
you find, or have your authorized 
Honda Marine dealer correct it, 
before you operate the outboard 
motor.

Before beginning your pre-operation 
checks, be sure the ignition switch is 
in the OFF position.

Improperly maintaining this 

outboard motor or failing to 

correct a problem before 

operation can cause a 

malfunction in which you 

could be seriously hurt or 

killed.

Always perform a pre-

operation inspection before 

each operation, and correct 

any problem.

31ZY96300.book  45 ページ  ２０１３年１０月２１日　月曜日　午前９時２５分

Содержание BF100D




























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды