Honda BF100D Скачать руководство пользователя страница 118

Страница: 118 / 155

116

TAKING CARE OF UNEXPECTED PROBLEMS

4. Use the fuse puller from the tool kit

to remove the fuses. If a fuse is

blown, install a replacement fuse of

the same specified rating. The

outboard motor is supplied with

spare fuses in the fuse holder.

MAIN FUSE RATINGS:



10 A, 15 A, 30 A

5. Reinstall the fuse case lid,

electrical parts cover, and the

engine cover.

6. Reconnect the battery.

Never use a fuse with a rating greater
than specified. Serious damage to the
electrical system could result.

If a blown fuse is found, try to
determine and correct the electrical
problem that caused the blown fuse.
An uncorrected electrical problem
may cause the fuse to blow again.

If fuses continue to blow, take the
outboard motor to an authorized
Honda Marine dealer for inspection
and service, or refer to the shop
manual.

ACG Fuse

1. Stop the engine and disconnect the

battery cable.

2. Remove the engine cover.

3. Remove the fuse case lid.

FUSE PULLER

‘‘70 A’’ MARK

SPARE FUSE (70 A)

FUSE CASE LID

ACG FUSE (70 A)

3 mm SCREWS

31ZY96300.book 116 ページ２０１３年１０月２１日　月曜日　午前９時２５分

Содержание BF100D




























































































































































Результаты поиска

Содержание BF100D

Отзывы:

Бренды по названию

Популярные бренды

Honda BF100D, Руководство пользователя

Результаты поиска

Содержание BF100D

Отзывы:

Бренды по названию

Популярные бренды