Honda BF100D Скачать руководство пользователя страница 101

Страница: 101 / 155

SERVICING YOUR OUTBOARD MOTOR

Portable Fuel Tank and Tank

Filter Cleaning



(optional equipment)

Fuel Tank

Empty the portable fuel tank into an
approved gasoline container. Use a
funnel to avoid spilling fuel. Rinse
the fuel tank with nonflammable
solvent to remove any accumulated
sediment.

Fuel Tank Filter

1. Remove the four 5 mm screws

using a flat screwdriver, and then

remove the fuel hose connector and

fuel tank filter from the tank.

2. Clean the filter in nonflammable

solvent. Inspect the fuel tank filter

and the connector gasket. Replace

them if damaged.

3. Reinstall the filter and hose

connector in the fuel tank. Tighten

the four 5 mm screws securely.

Gasoline is highly



flammable and explosive.

You can be burned or

seriously injured when



handling fuel.

• Stop the engine and keep

heat, sparks, and flame

away.

• Handle fuel only



outdoors.

• Wipe up spills



immediately.

FUEL HOSE

(standard equipment)

5 mm SCREWS (4)

CONNECTOR

GASKET

FUEL TANK FILTER JOINT

(Fuel Hose Connector)

FUEL TANK

FILTER

31ZY96300.book 99 ページ２０１３年１０月２１日　月曜日　午前９時２５分

Содержание BF100D




























































































































































Результаты поиска

Содержание BF100D

Отзывы:

Бренды по названию

Популярные бренды

Honda BF100D, Руководство пользователя

Результаты поиска

Содержание BF100D

Отзывы:

Бренды по названию

Популярные бренды