manualshive.com logo in svg

HONDA marine BF135A, Руководство по ремонту, Страница: 5 / 49

Поделиться
Скачать
HONDA marine BF135A Скачать руководство пользователя страница 5

5-2

2. TROUBLESHOOTING WITH 

Dr. H

• DTC (DIAGNOSTIC TROUBLE

CODE) CHECK

1. Remove the engine cover and the electric part cover

(Section 4 of the base manual).

2. Disconnect the 4P (Red) connector and connect the

Dr. H to the data link connector (DLC).

3. Turn the ignition switch ON and check the DTC

shown on the Dr. H.

Refer to the Dr. H's operation manual for how to use
the Dr. H.

• WHEN USING Dr. H DURING

CRUISING

1. Remove the engine cover and the electric part cover

(Section 4 of the base manual).

2. Remove the cap from the under cover front bracket.

Route the extension wire through the front cover
bracket.

• Set the grommet on the under cover front bracket

securely.

3. Disconnect the red 4P connector from the DLC

(Data Link Connector) and secure the DLC wire as
sown.

• Route the extension wire of the tester in the posi-

tion shown so that it does not interfere with the
parts.

4. Connect the extension wire to the DLC.

4P CONNECTOR
(RED)

TESTER WIRE

DATA LINK 
CONNECTOR (DLC)

CAP

EXTENSION WIRE
OF TESTER

CLAMP

DLC

UNDER COVER
FRONT BRACKET

TESTER WIRE

Содержание BF135A


















































Отзывы:

Нет отзывов