HONDA marine BF135A Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 49

HONDA marine BF135A Скачать руководство пользователя страница 18

5-15

• Neutral Switch Malfunction

• Before following test, perform the neutral position check.

Engine speed does not increase in gears (BF150A only).

1. Switch condition check with the Dr. H

-1. Turn the ignition switch OFF and connect the Dr. H.
-2. Turn the ignition switch ON and check the neutral

switch condition using the Dr. H.

Does the switch position agree with the indication
of the tester?
YES – Substitute a known-good ECM and recheck.
NO – Perform “2. Neutral switch line check”.

2. Neutral switch line check

-1. Turn the neutral switch OFF and disconnect the neutral

switch 2P connector.

-2. Check for the continuity between the No. 1

(Black/Blue) terminal of the neutral switch harness
side 2P connector and the engine ground.

Is there the continuity?
YES – Repair short in the wire of the main harness.
NO – Go to the step 3.

-3. Check for the continuity between the No. 2 (Black)

terminal of the neutral switch harness side 2P con-
nector and the engine ground.

Is there the continuity?
YES – Go to the step 4.
NO – Repair open in the main wire harness.

-4. Disconnect the ECM connector B.
-5. Check for the continuity between the No. 13

(Black/Blue) terminal of the ECM harness side con-
nector B and the No. 1 (Black/Blue) terminal of the
neutral switch harness side 2P connector.

Is there the continuity?
YES – Perform “3. Neutral switch check”.
NO – Repair open in the main harness.

3. Neutral switch check

-1. Turn the ignition switch OFF and disconnect the neu-

tral switch 2P connector.

-2. Check for the continuity between the No. 1 (Black)

terminal and the No. 2 (Black/Blue) terminal of the
neutral switch side 2P connector.

Is there the continuity with the gear in Neutral and
no continuity with the gear in other than Neutral?
YES – Substitute a known-good ECM and recheck.
NO – The neutral switch is faulty.

VIEWED FROM THE
TERMINAL SIDE

BLACK/BLUE

NEUTRAL SWITCH HARNESS
SIDE 2P CONNECTOR

VIEWED FROM THE
TERMINAL SIDE

NEUTRAL SWITCH HARNESS
SIDE 2P CONNECTOR

NEUTRAL SWITCH
HARNESS SIDE 2P
CONNECTOR

ECM CONNECTOR B

VIEWED FROM THE
TERMINAL SIDE

VIEWED FROM THE
TERMINAL SIDE

NEUTRAL SWITCH SIDE 2P
CONNECTOR

BLACK

NTSW
(BLACK/BLUE)

«
...
16
17
18
19
20
...
»

Содержание BF135A


















































Отзывы:

Нет отзывов