HONDA marine BF135A Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 49

HONDA marine BF135A Скачать руководство пользователя страница 17

5-14

4. Overheat indicator line check

-1. Turn the ignition switch OFF. Disconnect the Red

terminal of the indicator light and connect the Black
terminal to short.

-2. Turn the ignition switch ON and check the overheat

indicator light.

Does the overheat indicator light come ON?
YES – Repair open in the wire harness (between

the ECM and the indicator light).

NO – Go to the step 3.

-3. Turn the ignition switch OFF and connect the indicator

light Red terminal.

-4. Disconnect the remote control harness 14P connector.
-5. Check for the continuity between the No. 7 (Red) ter-

minal and the No. 2 (Black/Yellow) terminal of the
remote control harness side 14P connector.

Is there the continuity?
YES – Repair open in the wire of the main har-

ness.

NO – The indicator light is faulty or repair open in

the remote control harness.

5. Oil pressure indicator line check

-1. Turn the ignition switch OFF. Disconnect the Yellow

terminal of the indicator light and connect the Black
terminal to short.

-2. Turn the ignition switch ON and check the oil pres-

sure indicator light.

Does the oil pressure indicator light come ON?
YES – Go to the step 3.
NO – Repair open in the wire harness (between

the ECM and the indicator light).

-3. Turn the ignition switch OFF and connect the indica-

tor light Yellow terminal.

-4. Disconnect the remote control harness 14P connector.
-5. Check for the continuity between the No. 6 (Yellow)

and the No. 2 (Black/Yellow) terminals of the remote
control harness side 14P connector.

Is there the continuity?
YES – Repair open in the main harness.
NO – The indicator light is faulty or repair open in

the remote control harness wire.

VIEWED FROM THE
TERMINAL SIDE

REMOTE CONTROL
HARNESS SIDE 14P
CONNECTOR

VIEWED FROM THE
TERMINAL SIDE

REMOTE CONTROL
HARNESS SIDE 14P
CONNECTOR

BLACK/YELLOW

RED

BLACK/YELLOW

YELLOW

«
...
15
16
17
18
19
...
»

Содержание BF135A


















































Отзывы:

Нет отзывов