manualshive.com logo in svg

HONDA marine BF135A, Руководство по ремонту, Страница: 21 / 49

Поделиться
Скачать
HONDA marine BF135A Скачать руководство пользователя страница 21

5-18

DTC 3-2: MAP sensor voltage is high

1. Symptom reproduction test

-1. Connect the Dr. H and clear the DTC once. If the

DTC can not be cleared, go on the troubleshooting.

-2. Turn the ignition switch ON.
-3. Check PB voltage using the Dr. H.

Is the measured voltage 0.22 – 3.15V?
YES – Temporary failure (Disappeared)
NO – Perform “2. MAP sensor power line check”.

2. MAP sensor power line check

-1. Turn the ignition switch OFF and disconnect the

MAP sensor 3P connector.

-2. Turn the ignition switch ON.
-3. Measure the voltage between the No. 3 (Brown/Yellow)

terminal and the No. 1 (Green/Red) terminal of the
MAP sensor harness side 3P connector.

Is the measured voltage 4.75 – 5.25V?
YES – Perform “5. MAP sensor signal line open

circuit check”.

NO – Perform “3. MAP sensor power line open

circuit check”.

3. MAP sensor power line open circuit check

-1. Turn the ignition switch OFF and disconnect the

ECM connector B.

-2. Check for the continuity between the No. 3

(Brown/Yellow) terminal of the MAP sensor harness
side 3P connector and the No. 4 (Brown/Yellow) ter-
minal of the ECM harness side connector B.

Is there the continuity?
YES – Perform “4. MAP sensor ground line open

circuit check”.

NO – Repair open in the wire between the MAP

sensor and the ECM.

4. MAP sensor ground line open circuit check

-1. Check for the continuity between the No. 1

(Green/Red) terminal of the MAP sensor harness
side 3P connector and the body ground.

Is there the continuity?
YES – Perform “5. MAP sensor signal line open

circuit check”.

NO – Repair open in the wire between the MAP

sensor and the ECM.

5. MAP sensor signal line open circuit check

-1. Connect the ECM connector A.
-2. Turn the ignition switch ON.
-3. Measure the voltage between the No. 2 (White/Red)

terminal and the No. 1 (Green/Red) terminal of the
MAP sensor harness side 3P connector.

Is the measured voltage 4.75 – 5.25V?
YES – Perform “7. MAP sensor check”.
NO – Perform “6. MAP sensor signal line open

circuit check”.

MAP SENSOR HARNESS
SIDE 3P CONNECTOR

VCC1 
(BROWN/YELLOW)

VIEWED FROM THE
TERMINAL SIDE

SG1 
(GREEN/RED)

ECM CONNECTOR B

MAP SENSOR
HARNESS SIDE
3P CONNECTOR

VCC1 
(BROWN/YELLOW)

VIEWED FROM THE
TERMINAL SIDE

MAP SENSOR HARNESS
SIDE 3P CONNECTOR

SG1
(GREEN/RED)

VIEWED FROM THE
TERMINAL SIDE

MAP SENSOR HARNESS
SIDE 3P CONNECTOR

PB 
(WHITE/RED)

SG1 
(GREEN/RED)

VIEWED FROM THE
TERMINAL SIDE

Содержание BF135A


















































Отзывы:

Нет отзывов