manualshive.com logo in svg

Hommy HM116T, Руководство пользователя

Поделиться
Скачать
Hommy HM116T Скачать руководство пользователя страница 27

27

Troubleshooting guide (1):

NO.

Trouble

Possible cause

Solution

1

The machine doesn’t
work and the screen
displays

error

code”E8”

①Lack phase sequence.
② stirring shaft’s negative direction
rotation
③main circuit board doesn’t work.

① check the power supply and
wires
②、③replace the parts.

2

Stirring motor does
not work normally and
the screen displays
error code”E2”

① low voltage
②main stirring motor does not work.
③main circuit board does not work.
④a . c . Contactor does not work.
⑤over-current relay does not work.

①improve the power supply
②replace the motor
③ check the wires and plugs, or
replace the circuit board.
④、⑤replace the parts

3

the compressor does
not work properly.

①low voltage
②the compressor is broken.
③over-current relay does not work.
④main circuit board is broken.

①improve the power supply.
②replace the compressor
③replace the over-current relay.
④ check the wires and plugs, or
replace the main circuit board.

4

the mixer does not run ①the motor of mixer is broken.

②main circuit board is broken.
③the mixer cover is broken.

Replace the parts.

5

stirring motor works
continuously.

①the main circuit is broken.

Replace the parts.

6

ice cream is too soft
and the machine keep
working

on

refrigeration.

① the slurry is not enough in the
cylinder.
② ice cream becomes soft
③

the

plastic

scrappers

are

damaged.
④ The room temperature is above
40℃.
⑤the space for exhaust is not enough
⑥leak refrigerant
⑦ the settings of hardness is
incorrect.
⑧the temperature sensor is broken.

① pour more slurry into the

hopper.

② unfreeze and pour some new
slurry in the hopper , then
refrigerate again
③replace the plastic scrappers
④ 、 ⑤ improve the location
condition
⑥ repair the leak and fill in

refrigerant according to the
nameplate parameter.

⑦reset
⑧ replace the sensor of the
cylinder and circuit board

Содержание HM116T

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды