Holtek BC66F5652 Скачать руководство пользователя страница 84

Страница: 84 / 242

Rev. 1.10

October 23, 2020

Rev. 1.10

October 23, 2020

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

• PAWU Register

Bit

Name

PAWU7

PAWU6

PAWU5

PAWU4

PAWU3

PAWU2

PAWU1

PAWU0

R/W

POR

Bit 7~0

PAWU7~PAWU0

: PA7~PA0 wake-up function control

0: Disable

1: Enable

I/O Port Control Registers

Each I/O port has its own control register known as PAC~PDC, to control the input/output

configuration. With this control register, each CMOS output or input can be reconfigured

dynamically under software control. Each pin of the I/O ports is directly mapped to a bit in its

associated port control register. For the I/O pin to function as an input, the corresponding bit of the

control register must be written as a “1”. This will then allow the logic state of the input pin to be

directly read by instructions. When the corresponding bit of the control register is written as a “0”,

the I/O pin will be set as a CMOS output. If the pin is currently set as an output, instructions can still

be used to read the output register.
However, it should be noted that the program will in fact only read the status of the output data latch

and not the actual logic status of the output pin.

• PxC Register

Bit

Name

PxC7

PxC6

PxC5

PxC4

PxC3

PxC2

PxC1

PxC0

R/W

POR

PxCn

: I/O Port x Pin type selection

0: Output

1: Input

The PxCn bit is used to control the pin type selection. Here the “x” can be A, B, C or D.

However, the actual available bits for each I/O Port may be different.

Note that the PC3~PC6 lines are not connected to the external pins and the IRQ is pin-shared

with PA1, it is recommended that the corresponding PxCn bit should be properly configured

to implement correct connection and RF function control after power on. Refer to the “Pin-

shared Functions” section for more details.

I/O Port Source Current Control

The device supports different output source current driving capability for each I/O port. With the

selection register, SLEDCn, specific I/O port can support four levels of the source current driving

capability. These source current selection bits are available when the corresponding pin is configured

as a CMOS output. Otherwise, these select bits have no effect. Users should refer to the Input/Output

Characteristics section to select the desired output source current for different applications.

Register

Name

Bit

SLEDC0 SLEDC07 SLEDC06 SLEDC05 SLEDC04 SLEDC03 SLEDC02 SLEDC01 SLEDC00
SLEDC1

—

SLEDC15 SLEDC14

SLEDC11 SLEDC10

I/O Port Source Current Control Registers List

Содержание BC66F5652



















































































































































































































































Результаты поиска

Содержание BC66F5652

Отзывы:

Похожие инструкции для BC66F5652

Бренды по названию

Популярные бренды

Holtek BC66F5652, Руководство пользователя

Результаты поиска

Содержание BC66F5652

Отзывы:

Похожие инструкции для BC66F5652

Бренды по названию

Популярные бренды