manualshive.com logo in svg

Holtek BC66F5652, Руководство пользователя

Holtek BC66F5652 - усовершенствованный чип с Bluetooth, обеспечивающий высокое качество сигнала и надежное соединение. Получите подробную информацию об использовании устройства в руководстве пользователя. Скачайте бесплатное руководство на manualshive.com для удобного ознакомления с возможностями продукта.

Поделиться
Скачать
background image

Rev. 1.10

186

October 23, 2020

Rev. 1.10 

187

October 23, 2020

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

Comparator Interrupt

The comparator interrupt is controlled by the internal comparator. A comparator interrupt request 

will take place when the comparator interrupt request flag, CPF, is set, a situation that will occur 

when the comparator output bit changes state. To allow the program to branch to its respective 
interrupt vector address, the global interrupt enable bit, EMI, and comparator interrupt enable bit, 

CPE, must first be set. When the interrupt is enabled, the stack is not full and the comparator inputs 

generate a comparator output transition, a subroutine call to the comparator interrupt vector, will 

take place. When the interrupt is serviced, the comparator interrupt request flag will be automatically 

reset and the EMI bit will be automatically cleared to disable other interrupts.

Multi-function Interrupts

Within the device there are three Multi-function interrupts. Unlike the other independent interrupts, 
these interrupts have no independent source, but rather are formed from other existing interrupt 
sources, namely the TM interrupts, LVD interrupt and EEPROM erase or write operation interrupt.
A Multi-function interrupt request will take place when any of the Multi-function interrupt request 

flags MFnF are set. The Multi-function interrupt flag will be set when any of their included functions 
generate an interrupt request flag. To allow the program to branch to its respective interrupt vector 

address, when the Multi-function interrupt is enabled and the stack is not full, and any one of the 
interrupts contained within each of the Multi-function interrupt occurs, a subroutine call to the 
related Multi-function interrupt vector will take place. When the interrupt is serviced, the related 

Multi-function request flag will be automatically reset and the EMI bit will be automatically cleared 

to disable other interrupts.
However, it must be noted that, although the Multi-function Interrupt request flags will be 
automatically reset when the interrupt is serviced, the request flags from the original source of 
the Multi-function interrupt will not be automatically reset and must be manually reset by the 
application program.

A/D Converter Interrupt

The A/D Converter Interrupt is controlled by the termination of an A/D conversion process. An A/

D Converter Interrupt request will take place when the A/D Converter Interrupt request flag, ADF, 
is set, which occurs when the A/D conversion process finishes. To allow the program to branch to its 

respective interrupt vector address, the global interrupt enable bit, EMI, and A/D Interrupt enable bit, 

ADE, must first be set. When the interrupt is enabled, the stack is not full and the A/D conversion 

process has ended, a subroutine call to the A/D Converter Interrupt vector, will take place. When the 

interrupt is serviced, the A/D Converter Interrupt flag, ADF, will be automatically cleared. The EMI 

bit will also be automatically cleared to disable other interrupts.

Time Base Interrupts

The function of the Time Base Interrupt is to provide regular time signal in the form of an internal 

interrupt. They are controlled by the overflow signals from their respective timer functions. When 

these happen their respective interrupt request flags, TB0F or TB1F, will be set. To allow the 
program to branch to their respective interrupt vector addresses, the global interrupt enable bit, EMI 

and Time Base enable bit, TB0E or TB1E, must first be set. When the interrupt is enabled, the stack 
is not full and the Time Base overflows, a subroutine call to their respective vector locations will 
take place. When the interrupt is serviced, the respective interrupt request flag, TB0F or TB1F, will 

be automatically reset and the EMI bit will be cleared to disable other interrupts.

The purpose of the Time Base Interrupt is to provide an interrupt signal at fixed time periods. Their 

clock sources f

PSC0

 or f

PSC1

, originate from the internal clock source f

SYS

, f

SYS

/4 or f

SUB

 and then 

Содержание BC66F5652



















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BC66F5652

GEOSUN gAirHawk Operation Manual preview
gAirHawk
Бренд: GEOSUN Страницы: 9
Strong STR 8101 User Manual preview
STR 8101
Бренд: Strong Страницы: 23
C. Crane FM Transmitter 2 Operating Instructions Manual preview
FM Transmitter 2
Бренд: C. Crane Страницы: 13
Landmark FM720 Installation And User Information preview
FM720
Бренд: Landmark Страницы: 2
Eldat Easywave RTM08 Series Quick Start Manual preview
Easywave RTM08 Series
Бренд: Eldat Страницы: 2
C4Line C4L6400-2W-U Quick Start Manual preview
C4L6400-2W-U
Бренд: C4Line Страницы: 2
PowerBox Systems PowerBox Cockpit Instruction Manual preview
PowerBox Cockpit
Бренд: PowerBox Systems Страницы: 30
Smarthome AD30415 Installation And Operating Manual preview
AD30415
Бренд: Smarthome Страницы: 2
Laser SPK-WFADAPTOR Quick User Manual preview
SPK-WFADAPTOR
Бренд: Laser Страницы: 6
Ten-Tec T-KIT 1056 Instruction Manual preview
T-KIT 1056
Бренд: Ten-Tec Страницы: 12
Galaxy Innovations Avatar2 User Manual preview
Avatar2
Бренд: Galaxy Innovations Страницы: 48
ADN pesage T16F Installation And User Manual preview
T16F
Бренд: ADN pesage Страницы: 39
Larson Electronics DCP-16-DP-HD Instruction Manual preview
DCP-16-DP-HD
Бренд: Larson Electronics Страницы: 2
RCF IT 4000 Manual preview
IT 4000
Бренд: RCF Страницы: 4
AOR AR5000A Operating Manual preview
AR5000A
Бренд: AOR Страницы: 81
Broadata Communications LinkBridge LBC-HDBT-R-DG User Manual preview
LinkBridge LBC-HDBT-R-DG
Бренд: Broadata Communications Страницы: 14
Digi MIL-240FXC Installation Manual preview
MIL-240FXC
Бренд: Digi Страницы: 5
AEQ LIVE 20 TR User Manual preview
LIVE 20 TR
Бренд: AEQ Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды