Holtek BC66F5652 Скачать руководство пользователя страница 36

Страница: 36 / 242

Rev. 1.10

October 23, 2020

Rev. 1.10

October 23, 2020

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

BC66F5652

2.4GHz RF Transceiver A/D Flash MCU

• FD3H Register

Bit

Name

D15

D14

D13

D12

D11

D10

R/W

POR

Bit 7~0

D15~D8

: The fourth Flash Memory data bit 15 ~ bit 8

• FC0 Register

Bit

Name

CFWEN

FMOD2

FMOD1

FMOD0

FWPEN

FWT

FRDEN

FRD

R/W

POR

Bit 7

CFWEN:

Flash Memory Erase/Write function enable control

0: Flash Memory erase/write function is disabled

1: Flash Memory erase/write function has been successfully enabled

When this bit is cleared to zero by application program, the Flash Memory erase/write

function is disabled. Note that this bit cannot be set high by application programs.

Writing “1” into this bit results in no action. This bit is used to indicate that the Flash

Memory erase/write function status. When this bit is set high by hardware, it means

that the Flash Memory erase/write function is enabled successfully. Otherwise, the

Flash Memory erase/write function is disabled as the bit content is zero.

Bit 6~4

FMOD2~FMOD0:

Flash Memory Mode selection

000: Write Mode

001: Page Erase Mode

010: Reserved

011: Read Mode

100: Reserved

101: Reserved

110: Flash Memory Erase/Write function Enable Mode

111: Reserved

These bits are used to select the Flash Memory operation modes. Note that the “Flash

memory Erase/Write function Enable Mode” should first be successfully enabled

before the Erase or Write Flash memory operation is executed.

Bit 3

FWPEN:

Flash Memory Erase/Write function enable procedure trigger

0: Erase/Write function enable procedure is not triggered or procedure timer times

out

1: Erase/Write function enable procedure is triggered and procedure timer starts to

count

This bit is used to activate the flash memory Erase/Write function enable procedure

and an internal timer. It is set by the application programs and then cleared to zero by

the hardware when the internal timer times out. The correct patterns must be written

into the FD1L/FD1H, FD2L/FD2H and FD3L/FD3H register pairs respectively as

soon as possible after the FWPEN bit is set high.

Bit 2

FWT:

Flash Memory write initiate control

0: Do not initiate Flash Memory write or indicating that a Flash Memory write

process has completed

1: Initiate a Flash Memory write process

This bit is set by software and cleared to zero by the hardware when the Flash memory

write process has completed.

Bit 1

FRDEN:

Flash Memory read enabled bit

0: Flash Memory read disable

1: Flash Memory read enable

This is the Flash memory Read Enable bit which must be set high before any Flash

Содержание BC66F5652



















































































































































































































































Результаты поиска

Содержание BC66F5652

Отзывы:

Holtek BC66F5652, Руководство пользователя, Страница: 36 / 242

Результаты поиска

Содержание BC66F5652

Отзывы: