background image

9

XL-LG20004UM-en-US Rev B · 2018-09-17 · Amendments and Errors Reserved · © SAF-HOLLAND, Inc., SAF-HOLLAND, HOLLAND, SAF, 
and logos are trademarks of SAF-HOLLAND S.A., SAF-HOLLAND GmbH, and SAF-HOLLAND, Inc.

Welding Standards

The recommended welding gas for gas metal arc welding 
(GMAW) is 90% Argon / 10% CO2. If a different gas is used, 
welds MUST comply with penetration requirements illustrated 

(Figure 12).

 Where the installation drawing specifies 

different than above, the drawing shall prevail.

5.4 Procedures

Tack welds used for positioning components are to be located 
in the center of the final weld, where practical. Tack weld 
should be completely fused to the finish weld. DO NOT 
break arc at the end of the weld. Back up all finish welds 
at least 1/2" (12.7 mm) or a sufficient amount to prevent 
craters at the end of the weld. Where weld is shown to go 
around corners, it is assumed the corner represents a stress 
concentration area. DO NOT start or stop weld within  
1" (25.4 mm) of the corner. Particular care should be taken  
to prevent undercutting in this area.

5.5 Weld Size

If weld size is NOT specified, the effective throat of the weld 
MUST be no smaller than the thinnest material being welded 

(Figure 12)

.

LACK OF FUSION OF ANY 
KIND IN THIS AREA IS NOT  
ACCEPTABLE AT ANY TIME

PENETRATION AS MEASURED THROUGH SEAM

TARGET PENETRATION TO BE 
% OF THINNEST MATERIAL 
FROM INTERSECTION OF FILLET 
AS ILLUSTRATED

TARGET 
PENETRATION

5.  Welding Standards

5.1  Welding Standards

This specification applies to all components supplied by 
SAF-HOLLAND

®

, and its products. The customer assumes 

full responsibility for weld integrity if weld material and 
procedures differ from those listed below.

5.2 Workmanship

All welding on SAF-HOLLAND

®

 products MUST be performed 

by a welder qualified according to the appropriate AWS 
standard for the weld being made or an equivalent standard. 
It is the responsibility of the customer to provide good 
workmanship when welding on SAF-HOLLAND

®

 products.

5.3 Material

Items to be welded that are made from low carbon or high-
strength alloy steel are to be welded with AWS filler metal 
specification AWS A5.18, filler metal classification ER-70S-3, 
ER-70S-6 or equivalent unless specified on the  
installation drawing.

NOTE:

  Any substitution for filler material from the above 

standard MUST comply, as a minimum, with the 
following mechanical properties:

 

Tensile Strength - 72k psi (496 MPa)   
Yield Strength - 60k psi (414 MPa) 
Charpy V Notch - 20ft.-lbs. (27 N•m) at 0

F (-17.7

C)% 

Elongation - 22%

Figure 12

Содержание Atlas 55





















Отзывы: