background image

 

C 9.92

Operating Instructions

228

153 146

Alphabetical index

Page

Page

Changing the hydraulic oil (at least every 2 years) ...... 205
Changing the hydraulic oil (or at 1500 hours) ............... 213
Changing the toothed belt ........................................... 207
Changing the toothed belt (or at 3000 hours) ............... 215
Check the service brake ............................................. 177
Checking air tubes and air hoses for leaks .................. 167
Checking engine V-belt tension and condition .............. 169
Checking the accelerator for ease of movement,

clean and grease if necessary ............................. 200

Checking the air cleaner system,

cleaning if necessary ........................................... 185

Checking the air conditioner for proper operation ......... 197
Checking the air conditioner hoses and wiring

for damage ........................................................... 198

Checking the air tubes and air hoses for leaks ............ 193
Checking the battery, coating the terminals with

grease .................................................................. 210

Checking the brake fluid level .............................. 50, 196
Checking the brakes and steering for proper function .... 57
Checking the cable connections .................................. 196
Checking the condensate water drain .......................... 198
Checking the condenser for the free flow of air,

cleaning if necessary .................................. 189, 198

Checking the coolant, adding if necessary .................. 194
Checking the coolant level,

topping up if necessary ............................... 168, 194

Checking the electrical system for proper operation,

check the lighting ................................................. 199

Checking the engine for leaks ............................ 167, 193
Checking the engine oil level ................................ 46, 193
Checking the engine valve clearances ............... 182, 203
Checking the front and rear gearbox for leaks ............. 196
Checking the front and rear gearbox oil level ............... 196
Checking the frost protection

of the windshield washer water .................... 192, 200

Checking the fuel lines for condition and tightnes ........ 196
Checking the glow plugs .................................... 203, 213
Checking the heating hoses

for damage and tightness ............................ 169, 193

Checking the heating system for proper operation ....... 197
Checking the hydraulic lines and hoses for damage

and tightness ....................................................... 196

Checking the hydraulic lines and hoses and hoses

for leaks and damage ........................................... 170

Checking the hydraulic oil level ................... 48, 170, 196
Checking the lights and rear view mirror ........................ 53

Содержание C 9.92 H















































































































































































































































Отзывы: