Holder C 9.92 H Скачать руководство пользователя страница 103

Страница: 103 / 238

Operating Instructions

153 146

101

C 9.92

Operating the attachments

Push the push-pull rod in.
The PTO speed will be 1000 RPM at an engine speed
of 2390 RPM.

ATTENTION

Never turn the PTO on with the engine off!

Increase the engine speed to 1500-1800 RPM.

Release the lock at the safety switch (1) and depress
the switch. The front PTO is now turned on.

To turn the PTO off, press the safety switch (1) up.

If the PTO is no longer required, put the push-pull rod
(3) back to the neutral position.

DANGER

After the PTO is turned off, the installed at-
tachment could continue to run. Wait until the
attachment is stationary before working on it
again.

Bild_C992H_093

Bild_S 990_007

Содержание C 9.92 H















































































































































































































































Результаты поиска

Содержание C 9.92 H

Отзывы:

Похожие инструкции для C 9.92 H

Бренды по названию

Популярные бренды

Holder C 9.92 H, Руководство по эксплуатации

Результаты поиска

Содержание C 9.92 H

Отзывы:

Похожие инструкции для C 9.92 H

Бренды по названию

Популярные бренды