background image

instructions for

platform truck 450kg capacity

model no: 

cSt806

thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions, 

and properly maintained, give you years of trouble free performance.

IMPORTANT:

 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE 

THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR 
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

1.  SafEty

 

9

   Always distribute the load evenly over the surface of the bed of the platform truck.

 

8

  

Do Not

 leave unattended, especially when loaded, unless the wheels are chocked or the truck is otherwise secured.

 

8

  

Do Not

 use platform truck on uneven ground and do not run over kerbs or steps - use a ramp.

 

8

  

Do Not

 allow others to ride on the platform truck.

 

8

  

Do Not

 use the truck if any part is damaged, paying particular attention to the wheels. inspect it before use each time and replace  

  or repair damaged or worn parts immediately.

 

9

   check tyre pressures on the platform truck on a regular basis. 

 

8

  

Do Not

 over inflate the tyres. Recommended pressure is 25psi.

 

8

  

Do Not

 exceed maximum load capacity of 450kg.

 

8

  

Do Not

 allow children to play on, stand upon or climb on the cart.

 

9

   Be mindful of the location of the handle it may fall from the upright position.

 

9

   chock the wheels when loading and unloading the cart.

 

9

   alWayS

 use caution when operating the platform truck. When moving it, proceed at a safe speed, especially at corners where there  

  could be a danger of the load shifting. extra care should be taken on inclined surfaces.

 

8

  

Do Not

 use the platform truck when you are tired or under the influence of alcohol, drugs or intoxicating medication.

 

8

  

Do Not

 store material on the platform truck for an extended period of time.

2.  iNtroDuctioN

Heavy-duty rust resistant steel construction. smooth steering action for easy manoeuvrability with soft rubber gripped handle and pneumatic 

wheels for easy transportation over the toughest terrain. All four sides drop down using locking pin function for easy loading. can also be used 

as a flat bed for transporting oversized items. Fitted with additional removable storage tray for carrying smaller items. Suitable for a variety of 

warehouse, office, garden and domestic applications.

3.  SpEcificatioN

model No: .................................................................cSt806

maximum load capacity: ...............................................

450kg

W

heel size:

 ......................................................

Ø300 x 90mm

i

nternal size (length x width x depth):

 ....

1120 x 560 x 300mm

Platform height: ..........................................................

390mm

overall height: ............................................................

650mm

c

ST806| Issue:3(L) 16/05/17

Original Language Version

© Jack sealey limited

refer to 

instruction 

manual

Содержание CST806







Отзывы: