Hoefer PS300B Скачать руководство пользователя страница 9

 pviii

 pviii

Important user information

All users must read this entire manual to fully under-
stand the safe use of the PS300B.

 

 

WARNING!

 

The warning symbol 

highlights instructions that must be 
followed to avoid personal injury. It 
is important not to continue until all 
stated conditions are met and clearly 
understood. Read the instructions to 
avoid hazardous conditions. 

 CAUTION!

  The caution symbol high-

lights instructions that must be followed 
to avoid damage to the product or 
other equipment. It is important not to 
continue until all stated conditions are 
met and clearly understood. 

     Note:

 

 Note is used to indicate information 
important for trouble-free and optimal 
use of the product.

CE certification

This product meets the requirements of applicable  
CE-directives. A copy of the corresponding Declaration 
of Conformity is available on request.

The CE symbol and corresponding declaration of  
conformity is valid for the instrument when it is:

• used in a laboratory location, and

• used as a stand-alone unit, or

•  connected to other CE-marked Hoefer, Inc.  

instruments, or

•  connected to other products recommended or 

described in this manual, and 

•  used in the same state as it was delivered from 

Hoefer, Inc. except for alterations described in 
this manual.

Please read this entire manual 
to fully understand the safe and 
effective use of this product. 

If you have any comments on 
this manual, please send them 
to us at:

Hoefer, Inc. 
84 October Hill Road 
Holliston, MA 01746 
[email protected]

Hoefer, Inc. reserves the right to 
make changes in the specifica-
tions without prior notice.

Содержание PS300B


























Отзывы: