HNP Mikrosysteme mzr-2961 Скачать руководство пользователя

Страница: 37 / 58

7 Start Up / Shut Down

Operation manual mzr-2961, mzr-4661

Last update: April 2018

Technical data subject to change without prior notice!

7.5

Trouble shooting

If the pump does not start to operate or stops the operation abruptly, please

proceed as follows:

Try to liberate the micro annular gear pump:

−

by turning the potentiometer knob back and forth or by sending an analog

voltage signal

−

via the control software

−

by pressing with a syringe a suitable flushing liquid (see table 9 and table 10)

through the micro annular gear pump

−

by changing the operating direction of the pump.

If these measures turn out to be ineffective, please contact the service staff of

HNP Mikrosysteme (see chapter 11) and send the pump back to the

manufacturer for inspection.

Warning

You should under no condition try to dismantle the pump by yourself. This

may cause damage to the pump components and consequently annul your

warranty claims.

7.6

Return of the micro annular gear pump to the manufacturer

For the return of a micro annular gear pump and components that have already

been employed, please follow the instructions:

−

drain any remaining rests of the delivered liquid from the pump

−

flush the pump with an adapted solvent

−

remove the filter elements from integrated or loosely delivered filters

−

protect all openings against dust with the delivered protective plugs or

screws

−

return the pump in its original packing

The service personnel which carries out the repair should be informed about

the condition of the used micro annular gear pump. This is done by means of

the "Declaration of media in contact with the micro annular gear pump and

components" (see chapter 17). This form may also be downloaded from the

web site www.hnp-mikrosysteme.de/download.

The "Declaration of media in contact with the micro annular gear pump and

components" must imperatively be filled in. The nature of liquid which entered

into contact with the micro annular gear pump and the components must be

specified.

In case of non-compliance, the sender will be liable for any resulting injure to

persons or any object damage.

Содержание mzr-2961



























































Результаты поиска

Содержание mzr-2961

Отзывы:

Похожие инструкции для mzr-2961

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2961, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2961

Отзывы:

Похожие инструкции для mzr-2961

Бренды по названию

Популярные бренды