HNP Mikrosysteme mzr-2961 Скачать руководство пользователя

Страница: 17 / 58

4 Description of the pump

Operation manual mzr-2961, mzr-4661

Last update: April 2018

Technical data subject to change without prior notice!

liquid inlet

(suction side)

liquid outlet

(pressure side)

figure 8

Indication of the turning direction and fluidic connections on the front of the micro annular gear pump

4.2

Micro annular gear pump

The micro annular gear pumps

mzr

-2961 and

mzr

-4661 is provided with an

actuator equipped with a canned motor. The motor works high dynamically

and is recommended for dosage operation of the micro annular gear pump.

With this control unit it is possible to manage lower RPM ranges down to

400 RPM. For operating, it is recommended to use a power source of 24 V

(with a power rating of 2,5 A).

figure 9

Measures of the micro annular gear pump

The

mzr

-micro annular gear pump consists of the micro annular gear pump

head, the coupling unit and an actuator. The pump head is equipped with two

fluidic connector bore holes and a shaft for actuation of the rotors. The

coupling unit serves as connection between the pump head and the actuator as

well as to mount the micro annular gear pump.

The actuators used may be protected against dust, condensing moisture,

humidity, splashing, aggressive gases and liquids. Ensure sufficient ventilation

and therefore cooling of the motors.

The preferred position to assemble the micro annular gear pump is horizontal.

To avoid intruding fluids you may lay the pump under the actuator in vertical

operation.

The mechanical assembly of the pump may not be done over the fluidic

connectors or the motor.

Содержание mzr-2961



























































Результаты поиска

Содержание mzr-2961

Отзывы:

Похожие инструкции для mzr-2961

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-2961, Руководство по эксплуатации

Результаты поиска

Содержание mzr-2961

Отзывы:

Похожие инструкции для mzr-2961

Бренды по названию

Популярные бренды