HNP Mikrosysteme mzr-2961 Скачать руководство пользователя | Manualshive

Страница: 41 / 58

background image

10 Problems and their removal

Operation manual mzr-2961, mzr-4661

Last update: April 2018

Technical data subject to change without prior notice!

37

Disturbance

Cause

Solution

the manufacturer for cleansing.

Noise of beveling

The operation of the pump should
immediately be stopped! Return the pump to
the manufacturer for cleansing and repair.

The motor surface or the motor interior are
too hot.

High temperature indicator in the drive is on.
The motor has been shut down by the
thermistor. Return the pump to the
manufacturer.

18 The pump is noisy.

Wear out of the pump or defective
components.

Do not continue to operate the pump, return
it to the manufacturer for maintenance.

19 Overcurrent

Particles in the delivered liquid

Rinse the pump.

The pump operates with difficulty.

Dosing needle is damaged. Needle should be
cleansed, flushed or exchanged.

Tubing on the delivery side, dosing needle or
the non-return valve is blocked. Cleanse,
flush or exchange the components.

Deposits inside the pump.

Flush the pump. If necessary return the pump
to the manufacturer.

20 Undervoltage

Voltage supply < 12 VDC

Check the power supply 24 VDC

21 Overvoltage

Voltage supply > 28 VDC

Check the power supply 24 VDC. The drive
control unit may be damaged. Return the
pump to the manufacturer.

table 12

Problem shooting

!

If a disturbance that has not been mentioned in the above list, or that makes

the use of the micro annular gear pump unsafe appears, please stop the

operation of the pump without delay and contact HNP Mikrosysteme (see

chapter 11). If needed return the pump to the manufacturer for checkup.

«
...
39
40
41
42
43
...
»

Содержание mzr-2961



























































Отзывы:

Нет отзывов

Похожие инструкции для mzr-2961

Бренд: A.O. Smith Страницы: 2

Бренд: DAB Страницы: 13

Бренд: Watts Страницы: 37

Бренд: EINHELL Страницы: 44

SUPER T T6A60S-4LE2X FT4 Series

Бренд: GORMAN-RUPP PUMPS Страницы: 48

Бренд: Pfeiffer Vacuum Страницы: 40

Бренд: Oasis Aquatics Страницы: 14

RediHeat RH-120

Бренд: Spirax Sarco Страницы: 12

Бренд: Black Knight Страницы: 15

Бренд: Quantum Страницы: 36

Бренд: Danfoss Страницы: 4

Бренд: VAC-CON Страницы: 16

Бренд: Bock Water heaters Страницы: 60

Бренд: Kohler Страницы: 24

Бренд: SKAMET Страницы: 3

Poolex MEGALINE FI

Бренд: poolstar Страницы: 38

Бренд: Ironton Страницы: 17

Бренд: Simer Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды