HNP Mikrosysteme mzr-11507 Скачать руководство пользователя страница 8

Страница: 8 / 68

1 General information

Operating manual mzr-11557 Ex

Technical data subject to change without prior notice!

Last update: March 2019

Warning

The material properties of a liquid (e.g. viscosity, lubricating property, particle

content, corrosiveness) impacts the technical data and the lifetime of pumps.

Under appropriate conditions the characteristic values may be increased or

decreased.

Warning

If you intend to operate the pump out of the range of the above given

specification, please consult the manufacturer. Modifications may be necessary

to ensure successful operation. Otherwise the pump or the system may be

damaged seriously.

Warning

Starting the pump in dry condition might lead to damage of functional

components of the pump. Therefore, it is necessary to have the pump primed

(prefilled), and also in further operation please ensure a continuous supply of

liquid. Dry running of the pump has to be avoided.
The user is liable for damages caused by, any consequence with the non-

compliance of this instruction.

Содержание mzr-11507





































































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды