HNP Mikrosysteme mzr-11507 Скачать руководство пользователя страница 16

Страница: 16 / 68

3 Transport and intermediate storage

Operating manual mzr-11557 Ex

Technical data subject to change without prior notice!

Last update: March 2019

Transport and intermediate storage

3.1

Shipment of the pumps and protection measures

The pumps leaving the factory are secured against corrosion and shocks. The

inlets and outlets of the pumps are protected with plastic plugs in order to

prevent any foreign bodies from penetrating into the device.

3.2

Transport

In order to avoid any damage related to transport, the package must be

protected against shocks. HNP Mikrosysteme guarantees, that all goods leave

the factory in the best condition. Any noticed damage should be reported to

the concerned forwarding agent, authorized dealer or to HNP Mikrosysteme, as

manufacturer.

3.3

Intermediate storage

Following points concerning pump storage should be observed:

−

Necessary conservation procedure (see also chapter 8.7.1)

−

The protective plugs must be left screwed in

−

The pump should not be stored in humid places

−

For storage temperature - refer to chapter 1.3 of the present manual

Содержание mzr-11507





































































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды