HNP Mikrosysteme mzr-11507 Скачать руководство пользователя страница 46

Страница: 46 / 68

12 Maintenance and service

Operating manual mzr-11557 Ex

Technical data subject to change without prior notice!

Last update: March 2019

Maintenance and service

12.1

Micro annular gear pumps

The first maintenance of the micro annular gear pumps has to take place after

4000 hours or after 6 month latest. If wear is low at the first inspection further

maintenance intervals at the same operation conditions can be extended to

6000 hours or to a service interval of 12 month latest.

If there is increased wear at the first inspection the maintenance intervals have

to be adapted according to the wear situation.

In case of maintenance and service please send the micro annular gear pump to

your distributor or HNP Mikrosysteme directly. The address you may find on the

front page of the manual or in section 1.

The micro annular gear pump is sealed. It is prohibited to open or disassemble

the pump. The warranty will expire immediately in such a case.

HNP Mikrosysteme cannot give any warranty for replacing in case of damages

to the pump which are related to faulty operation.

12.2

Metal bellow-type coupling

Maintenance of the standard metal bellow-type coupling is not necessary

according to the enclosed manufacturer’s data when assembled by

HNP Mikrosysteme.

Within the maintenance intervals of the pump the screw tightenining torque

must be checked after 6000 hours. If at the first inspection damage at the

metal bellow-type coupling is found the maintenance intervals have to be

adapted according to the operational data. This check must be part of the

maintenance intervals of the micro annular gear pump.

12.3

Ex-Motor

The explosion proof motor itself is maintenance free. According to the

manufacturer’s instruction the explosion proof motor has to be checked 1-2

times per year regarding cracks and damages. This check must be part of the

maintenance intervals of the micro annular gear pump.

Содержание mzr-11507





































































Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды

HNP Mikrosysteme mzr-11507, Руководство по эксплуатации

Результаты поиска

Содержание mzr-11507

Отзывы:

Похожие инструкции для mzr-11507

Бренды по названию

Популярные бренды