HLF 4600 G1 Скачать руководство пользователя | Manualshive

Страница: 71 / 73

background image

TROUBLESHOOTING

I.M. HLF 4600 G1/2/F Eng V2-2010

71

HLF Italian Design

10 Troubleshooting

During operation, the computer board monitors the operating status continually. Faults
are displayed on the LCD display. In case of malfunctions, the user / operator can
intervene in accordance with the procedures described in this chapter and attempt to
troubleshoot the problem.

10.1 Checklist for fault diagnosis and troubleshooting

Error messages

Cause of fault

Troubleshooting measure(s)

C A U T I O N
Out of Coffee

1. Coffee beans hopper

empty or closed

2. The coffee grinder is

blocked

1. Re-fill coffee beans hopper

with fresh coffee beans

2. Contact the Service and

Support

C A U T I O N
Check Water

1. The water line is close

or the water runs very
slowly

2. The inlet water valve

is damaged (if used)

1. Open the water line valve

or contact the plumbing
department

2. Contact the Service and

Support for replacement

C A U T I O N
Drip Tray Full

1. The drip tray is full of

waste water

2. Check if the drip tray

micro switch is out of
order.

1. Remove the tray, empty

and clean it.

2. Check if the plastic float

inside the drip tray is free
to move

3. Contact the Service and

Support for replacement

Door Open

The front door or the right
side panel is open

Close the door or the right side
panel

Descaling/Filter

1. It’s programmed to do

a descaling process

2. It’s programmed to

change the descaling
filter

1. Need a descaling process.

2. Contact the Service and

Support for replacement

Grounds Drawer

The coffee grounds
drawer is full.

Empty the coffee grounds
drawer, open the front door
and tap the cleaning button

«
...
69
70
71
72
73
»

Содержание 4600 G1










































































Отзывы:

Нет отзывов

Похожие инструкции для 4600 G1

Бренд: Gaggenau Страницы: 7

Бренд: Gaggenau Страницы: 24

Бренд: Gaggenau Страницы: 24

Бренд: Gaggenau Страницы: 6

Бренд: Kees van der Westen Страницы: 26

Бренд: Kees van der Westen Страницы: 54

Mirage Slim Jim

Бренд: Kees van der Westen Страницы: 32

SCLUSIVO DCF210TTC

Бренд: DeLonghi Страницы: 1

Бренд: MACAP Страницы: 8

Бренд: Candi Страницы: 16

Бренд: NewAir Страницы: 11

Бренд: DèLonghi Страницы: 9

42820 Design Bread Maker Plus

Бренд: Gastroback Страницы: 32

Бренд: bonVIVO Страницы: 2

TM-T88IV ReStick

Бренд: Epson Страницы: 104

Бренд: Epson Страницы: 115

Бренд: Epson Страницы: 101

Бренд: Epson Страницы: 137

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды