Hitecsa CCHBA/CCHA 1201 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 35

Hitecsa CCHBA/CCHA 1201 Скачать руководство пользователя страница 26

26

IOM_WPVBZ HE-WPVZ HE_401-1201-4002_208110_200901_EN

PACKAGED COMPACT VERTICAL

– WATER / AIR

WPVBZ HE / WPVZ HE

OPERATION

EC MOTOR FANS

Working on the device

Danger due to electric current

Beware, hot surface!

Modifications / interventions in the device

Use genuine spare parts / genuine accessories only from the fan manufacturer. These parts have been designed
specially for the equipment. There is no guarantee that parts from non-original sources meet the load and safety
requirements.

The manufacturer does not approve the use of parts and optional equipment supplied by other manufacturers.



The rotor is not protected against indirect contact neither by supplementary or reinforced
insulation nor by connection to safety-earth in accordance with EN 60204-1, therefore, the
system constructor must provide protection by enclosure in accordance with EN 61140 before
the motor is connected to a power source. This protection can be achieved for example by a
guard grille (Product overview: Application operational area and Installation: General).

Temperatures of above 85ºC can occur on the motor surface, especially on the controller housing!

For safety reasons, it is forbidden to realize on your own any intervention or modification on the device. All planned

modifications must be approved by the manufacturer in writing.

WARNING!

WARNING!

WARNING!

«
...
24
25
26
27
28
...
»

Содержание CCHBA/CCHA 1201




































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды